background image

6 — DigiRoller

Plus II

Units of Measurement Key

— Selects desired unit 

format: Feet-Inches, Decimal Feet, Decimal Inches,
Yards, Meters, and Acres (area display only). Each press
of  this key will convert the displayed measurement to
another unit format.

Delete/All Clear Key

— Deletes, or erases, the values

stored in the next key pressed (e.g., 

[DEL] [L]

deletes

the current measurement stored as length, 

[DEL] [W]

deletes the current measurement stored as width,
etc). To perform an All Clear, press 

[Set] [DEL] [DEL]

.

This key sequence will clear all stored data and 
memory registers.

Recall Key

— Recalls and displays the value of the

next key pressed (for example, 

[Rcl] [W]

displays the

value stored in the Width key). 

[Rcl] [Rcl]

will recall

a previously rolled value that has been cleared or
deleted.

Memory Add Key

— Stores any displayed value into

permanent memory. When you store a value in 
memory, it is added to the values you previously
stored in memory. Note that you cannot add two
measurements of different levels of dimensions (for
example, you cannot add feet-inches and square feet).

Memory Subtract Key

— Subtracts the displayed

value from permanent memory.

Summary of Contents for 6425

































































Reviews: