SLEEP MODE
The Sleep Mode operation is a feature that minimizes pump operation
during quiet evening hours. For example, if Filter Cycle 1 (F1) is set to
activate at 8:00 a.m., by default, Filter Cycle 2 (F2) will activate at 8:00
p.m. (12 hours later). During 8:00 p.m. to 8:00 a.m., if the spa should call
for heat, the pump and heater will activate to heat the spa under normal
temperature demand. However, when in Sleep Mode, should the spa call
for heat, the pump and heater will be suspended after Filter Cycle 2 (F2)
until the activation of Filter Cycle 1 (F1), at 8:00 a.m. to minimize pump
activation during quiet evening hours.
Important:
Power-up of the spa starts the F1 sequence. In order for the
sleep mode to work in the evening hours, the spa must be powered up in
the early morning hours. The Sleep Mode will always be active the 6-12
hours between the end of (F2) and the beginning of (F1) depending on
how the filter cycle program is set.
Note:
If temperature drops below 27º C (80º F), heater will automatically
activate to prevent spa from freezing.
To activate Sleep Mode feature:
A. Press the MODE (
or
) button until the
TOOLS screen is displayed.
B. Press the
(+)
button to enter the TOOLS
submenus.
C. Press the MODE (
or
) button until ECON is displayed
.
D. Press the
(+)
button to activate Sleep Mode. Moon & Stars icon will
appear on the screen of the control panel, indicating this feature has
been activated.
To deactivate this feature, simply repeat steps A-C then press the
(-)
button.
FILTER CYCLES
When the spa is first powered up, the automatic filter cycle will
wait 10 minutes before starting. Your spa will automatically turn the first
filter cycle on for 60 minutes on low speed. The second filter cycle will
activate for 30 minutes, 12 hours later. The filter cycle icon, F1 or F2 will
be displayed in the control panel during the filter cycle.
NOTE:
The optional ozone system only works during the filter cycle.
To modify the length of either filter cycle:
A. Press the MODE (
or
) button until the
TOOLS menu is displayed.
B. Press the
(+)
button to enter the TOOLS
submenus.
C. Press the MODE (
or
) button until
FILT1 or FILT2 is displayed.
D. Press the
(+)
button to enter FILT1 or
FILT2. F1 or F2 icon will flash
.
E. Using the
(+)
or the
(-)
button, adjust the
desired filter cycle time, from 0 to 6 hours.
The filter cycle will activate the jet pump on low
speed for the entire cycle. When activated, the filter cycle icon on the
display is turned on. If the temperature exceeds the set point by three
degrees F for more than three hours, the system will cancel the filter
cycle for the remaining filter cycle time. Should the temperature cool
down to 1.5 degrees F (1 degree C) below the set point before the end
of the cycle, the cycle will resume for the rest of the time. Should you
use the spa during the filter cycle by placing the jet pump on high speed,
the Filter icon and Jets icon will be on. Once the jet pump has been shut
off, a ten minute tranquil mode begins (Filter & Jet icons are off during
tranquil mode while F1 or F2 remain lit). The Filter and Jet icons will
come back on once the tranquil mode ends if the filter cycle timer is still
on.
BRIGHTNESS - LCD
If you would like to change the brightness of the Control Panel screen:
A. Press the MODE (
or
) button until
the TOOLS menu is displayed.
B. Press the
(+)
button to enter the TOOLS
submenus.
C. Press the MODE (
or
) button until LCD is displayed.
D. Press the
(+)
button to enter into the LCD menu.
E. Using the
(+)
or the
(-)
button, adjust the desired screen brightness.
AUDIO MENU (OPTIONAL)
The following applies to spas that have an optional wireless audio system
installed:
When the wireless audio system has been installed on the spa, the
control panel can be used to control the audio system. The following
information demonstrates how to navigate the music menu by using the
spa’s control panel.
AUDIO MENU
Once the music system is installed, an AUDIO
menu will be accessible on the control panel
screen.
To access the menu, press the MODE (
or
)
button until AUDIO is displayed.
BASIC CONTROL PANEL OPERATION
1. To enter into a sub-menu press the
(+)
button.
2. To move to the next menu press the MODE (
) button
3. To exit from any sub-menu, press MODE (
or
) button as many
times as necessary until EXIT is displayed then press the
(+)
button
to exit that sub-menu.
TO TURN AUDIO SYSTEM ON/OFF
From the AUDIO screen:
1. Press the
(+)
button to display POWR -.
2. Press the
(+)
button to display POWR +
and turn the audio system ON. Press the
(-)
button to
display PWR - and turn the audio system OFF.
IMPORTANT:
The power can take a few seconds to turn on or off.
TO PAIR BLUETOOTH
On your device, find
My Spa BTXR
. If you DO NOT see this, another
device may already be connected (see To Disconnect Bluetooth on
following page).
1. Press the MODE (
or
) button until the SETUP screen is
displayed.
2. Press the
(+)
button to display one of three audio sources, BLUE,TV,
AUX in the setup menu. Bluetooth should be selected.
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
POWER
19
Operating Instructions
Summary of Contents for Aventine
Page 1: ...VACANZA SERIES 2 0 1 7 O W N E R S M A N U A L 5 0 H z...
Page 38: ......
Page 39: ......
