TEMPERATURE CONTROL
Press the actual temperature on Home screen to
display Set Temperature screen.
The set temperature range is from
80°F to 104°F (26°C to 40°C).
NOTE
: The water temperature
may vary depending on the current
use and condition of your spa and
outside temperatures.
The factory set temperature of the spa water is 100°F (38°C).
The last temperature value set by the user will be stored in memory. If
power is disconnected from the spa, it will automatically revert to the last set
temperature when power is reapplied.
Press to raise set temperature of spa. Press and hold to
raise the temperature continuously.
Press to lower set temperature of spa. Press and hold to
lower the temperature continuously.
MEMORY SCREEN
Press
on Home screen to display Memory screen.
Press to activate the last saved set of
operating functions.
Press to save the current set of operating
functions (jets and lights only).
Press to return to home screen if neither
of the above buttons are used. Screen
will automatically revert back after 10
seconds of non activity.
CLEAN CYCLE SCREEN
Press on Home screen to display Clean Cycle screen.
Press to start the
manual Clean Cycle.The screen
will briefly display CLEAN CYCLE:
ACTIVE. Activates jet pump 1 on
high speed for a ten minute
period
AUTO
CLEAN CYCLE:
START
ON
OFF
Press & hold to activate and deactivate the Auto
Clean Cycle. If activated, a clean cycle will run
every 24 hours starting at the time ON was first
pressed (runs Jet 2 for 1 minute and Jet 1 for 9
minutes)
Press to return to Home screen. Screen will
automatically revert back after 10 seconds of non
activity.
VANISHING ACT CYCLE
Press
38.5
C
on Home screen to display the
VANISHING ACT
screen.
Press to start the
VANISHING ACT
cycle activating
the low speed jet pump for 6 hours, ONLY to be used
with
VANISHING ACT
(see page 11)
SETTINGS SCREENS
Press on Home screen to display first Settings Screen.
The first Settings screen allows
you to turn Temperature Lock, Spa
Lock, Lights Timer and Summer
Timer On or Off.
TEMPERATURE LOCK
Press on Home screen to display Temperature Lock.
The Temperature Lock feature
prevents changing the desired
water temperature setting. All other
control panel functions will operate
normally while the Temperature Lock is "ON".
Press and hold ON or OFF for
approximately 4 seconds
to activate
or deactivate.
SPA LOCK
Press on Home screen to display Spa Lock.
When activated, the Spa Lock
feature disables all functions on the
control panel.
The control panel will not respond to
anything except on the Home screen.
Press and hold ON or OFF for
approximately 4 seconds
to activate
or deactivate.
LIGHTS TIMER
Press on Home screen to display Lights Timer.
When activated, the exterior lights
of the spa will come on 5 seconds
later will remain lit for 6 hours and
repeat the cycle every 24 hours from activation time.
Press ON or OFF to activate or deactivate.
SUMMER TIMER
Press on Home screen to display Summer Timer.
The Summer Timer can be activated during extremely hot summer
months to help maintain set water
temperatures.
• Activating the Summer Timer
causes the heater to immediately shut down. The circulation pump
will remain on for approximately 5 minutes pushing water through
the heater to cool it down.
MEMORY:
RESTORE
SAVE
AUTO
CLEAN CYCLE:
START
ON
OFF
VANISHING ACT®:
START
SETTINGS
TEMPERATURE LOCK
OFF
ON
SPA LOCK
OFF
ON
LIGHTS TIMER
OFF
ON
SUMMER TIMER
OFF
ON
SETTINGS
TEMPERATURE LOCK
OFF
ON
SPA LOCK
OFF
ON
LIGHTS TIMER
OFF
ON
SUMMER TIMER
OFF
ON
SETTINGS
TEMPERATURE LOCK
OFF
ON
SPA LOCK
OFF
ON
LIGHTS TIMER
OFF
ON
SUMMER TIMER
OFF
ON
SETTINGS
TEMPERATURE LOCK
OFF
ON
SPA LOCK
OFF
ON
LIGHTS TIMER
OFF
ON
SUMMER TIMER
OFF
ON
SETTINGS
TEMPERATURE LOCK
OFF
ON
SPA LOCK
OFF
ON
LIGHTS TIMER
OFF
ON
SUMMER TIMER
OFF
ON
Page 15
Operating Instructions
AUTO
CLEAN CYCLE:
START
ON
OFF
VANISHING ACT®:
START
Summary of Contents for CalderaSpas Utopia Series
Page 1: ...2 0 2 2 O W N E R S M A N U A L Utopia Series ...
Page 39: ......
