background image

Your Caldera

®

spa offers numerous ways for you to customize your massage experience. Experimentation is the best way to find what feels best to you. Try sitting in

different seats, adjusting the diverter valves, air controls, and jet nozzles and turning each pump on or off.

DIVERTER VALVES

The diverter valves on your spa allow you to direct the flow of water from the pumps to
various combinations of jets. The functions of these diverter valves can best be learned
by experimentation as follows:

1. Set all air controls to the “ON” position by rotating counterclockwise.

2. Turn on both pumps.

3. Turn the handle on each diverter valve and see which groups of jets are affected.

(

Note:

You can adjust the diverter valves to any position between the two possible

extremes to achieve the jet pressure that feels best to you.)

IMPORTANT: 

Your spa is not designed to provide full power to all jets when the diverter

valves are in the “mid” position. However, with the diverter valve in this position, you
may increase the power to selected jets by rotating the face of the VersaSsage

® 

,

MagnaSsage and Magna jets to close the ones that are not in use.

TIP: 

Turn both pumps on and place the diverter valves to the “Mid-Position”, then experiment with each of the air controls to see their effect.

WATERFALL VALVE

The Moorea

TM

spa is equipped with a cascading waterfall feature. It is activated by pressing JETS2 and turning the valve,

located on the front interior wall, counterclockwise. The flow is regulated by turning the waterfall valve to the desired position.

AIR CONTROLS

Each jet system has its own air control. These allow you to change the power of the jets by regulating the
amount of air that is mixed with the water coming out of the jets.

HYDRO JETS

Magna Jets -

These jets allow you to redirect the jet stream by changing the position of the nozzle.

MagnaSsage Jets -

These jets provide a rotating massage pattern.

The nozzles in the Magna jets and the MagnaSsage jets are interchangeable. To remove a MagnaSsage
rotating nozzle, ensure it is vertical and using your forefinger, ‘pop’ it out of the jet face. To install, align and
push straight in, the nozzle will snap into place. To remove, or install a standard Magna jet nozzle, rotate the
tabs on either side of the nozzle. Additional MagnaSsage dual-port nozzles are available from your Caldera
dealer.

Both the Magna and MagnaSsage jets allow you to regulate the force of the massage. Rotate the fascia ring
clockwise to reduce the force, or counter-clockwise to increase the force. Notice that turning off the flow to
some jets increases the flow to the other jets. To avoid damage to your spa’s plumbing and components, 
do not turn off more than half of these jets at the same time. 

CUSTOMIZING YOUR  MASSAGE

13

Position 1 -

The full flow

is directed to one series
of jets.

Mid-Position -

Positioning the diverter
at any point between
position one and two
divides the flow between
the jet systems.

Position 2 -

The full flow

is directed to a second
series of jets.

Magna

Jet

MagnaSsage

Jet

Summary of Contents for Hawaiian









































Reviews: