CalderaSpas PALATINO, Owner'S Manual

o

peratInG

 I

nStructIonS

CONTROL OPERATION

Your control panel consists of an LCD display and convenient touch pads 

that allow you to set the water temperature and adjust the skim/filter 

cycle settings, lock spa temp, lock all spa functions, as well as control the 

hydrotherapy jets, and lights.

LCD DISPLAY INVERSION

You may invert the control panel display for easier viewing from inside the 

spa. To invert the display the following is required: Press the MODE(



) 

and (-) buttons simultaneously. By pressing the MODE(



) and (-) buttons 

simultaneously a second time the screen will go back to it’s original 

display.

MODE BUTTON

From the Home screen use the 

MODE

 (



 or 



) button to scroll to the 

System, Clean, Audio (if your spa is equipped) and Tools screen. Press 

the 

(+) 

button to enter into the sub screens.

TEMPERATURE CONTROL

The set temperature range is from 26°C 

(80°F) to 40°C (104°F). Whenever power is 

disconnected and then reconnected to the spa, 

the water temperature setting will automatically 

return to the last temperature entered into the program. 
To increase the set temperature, press the

 (+)

 button, once for each 

degree of increase temperature desired. If you hold the

 (+) 

button down, 

the set temperature will increase by one degree every half second.

To decrease the set temperature, press the 

(-)

 button, once for each degree of 

decreased temperature desired. If you hold the 

(-) 

button down, the set temperature 

will decrease by one degree every half second. When the spa water has reached 

the set temperature, the “READY” icon will display.

JET PUMP CONTROL

Pressing the “JETS” button changes the jet pump functions, depending 

on the number of presses:

PALATINO

 AND 

MARINO

 SPA MODELS 

ONLY:

1st  press:   System 1 jet pump runs on low 

speed

2nd press:   System 1 jet pump runs on high 

speed

3rd press:    System 1 & System 2 jet pumps 

run on 

    high speed

4th press: 

   System 2 jet pump runs on high speed 

5th press: 

   Both Systems jet pumps are off

CAPITOLO

, 

CELIO

 & 

AVENTINE

 SPA 

MODELS ONLY:

1st press:    System 1 jet pump runs on low speed

2nd press:   System 1 jet pump runs on high speed

3rd press:    Jet pump off

•  The pump on high speed automatically turns off after operating 

for one hour. The pump on low speed automatically turns off after 

operating for one hour.

•  When the jets are active, the JETS icon on the control panel will 

illuminate.

 LIGHT ON/OFF & INTENSITY  

CONTROLS 

The light control uses four positions: High, Medium, Low, and Off. To turn 

on the spa light, press the LIGHT button. This will place all lights in the 

spa in the High, or maximum intensity position. When the lights turn on, 

the light symbol will also illuminate on the control panel display. Press 

the LIGHT button again to lower the intensity of the lights to the Medium 

position. Press the LIGHT button again to lower the intensity even more, 

placing the lights intensity in the Low position. Press the LIGHT button 

one more time to shut the lights off. When the light is deactivated, the 

light symbol will also turn off. 
If the lights are left on, they will automatically be turned off by the control 

system after 6 hours of continuous operation. The light symbol on the 

panel will also turn off when the lights are deactivated.
If the lights will not turn on, make sure SPA LOCK is deactivated. SPA 

LOCK disables the controls on the control panel (see following pages for 

more information on SPA LOCK).

SYSTEM MODE

Your spa is equipped with a System Mode. 

This function will allow you to conveniently 

turn the jet(s) on high speed and the light on 

maximum intensity at the same time.
To activate the system mode, perform the following functions:

17

Light Icon

Filter Cycle Icon

Jets Button

Light Button

Temperature 

Down/Off

Temperature 

Up /On

Mode 



Power Icon

Sleep 

Icon

Temp Ready

 Icon

Filter Cycle 2 

Icon

Filter Cycle 

1 Icon

Jet Icon

Mode 



SET

READY

F1

F2

READY

READY

READY

READY

READY

READY

READY

F1

READY

F1

F2

SET

F1

F2

SET

READY

F1

F2

READY

POWER

POWER

POWER

POWER

POWER

POWER

POWER

READY

F1

F2

POWER

Operating Instructions