OPERATING INSTRUCTIONS
19
Clean CYCle
The Clean Cycle has been provided as a convenient timer for water maintenance. When the cycle is activated, jet pump 1 will turn on and run for ten
minutes (used for water maintenance). To activate the Clean Cycle, press the "MODE
" or "MODE
" button until the
TOOLS
menu is displayed.
Then press the "ON
" button to enter the
TOOLS
submenus. The word
CLEAN
will be displayed (the CLEAN mode is the first submenu) on the
display. Press the "ON
" button to activate the Clean Cycle feature.
NOTE:
The jet icon will flash on and off in the main display while the Clean cycle is active.
To stop the Clean Cycle before the ten minutes is complete, Press the "MODE
" button until the
TOOLS
menu is displayed then press the "ON
" button to enter the
TOOLS
submenus where the word
CLEAN
is displayed on the screen. Press the "OFF
"
button to deactivate.
NOTE:
Pressing the "JETS" button will also deactivate the clean cycle.
lOCkInG FeaTures
The two locking features, SPA LOCK and TEMPERATURE LOCK, are enabled from the control panel by pressing the "MODE
" or "MODE
" button until the
TOOLS
menu is displayed. Then press the "ON
" button to enter the
TOOLS
submenus. Use the "MODE
" or "MODE
" button to scroll through the submenus to get to the
locking features. Once enabled, a lock will remain active until the specific button combination is applied to disable the lock. Even if power is disconnected from the hot tub
and soon thereafter reapplied (such as in a power outage) the lock will remain in place.
TeMPeraTure lOCk
The TEMPERATURE LOCK feature deactivates the temperature control function of the control panel. The JETS and the LIGHTS functions will operate normally.
TEMPERATURE LOCK is most often used by people who do not want others to tamper with or change the set temperature of the hot tub water.
TEMPERATURE LOCK is a submenu of the
TOOLS
menu.
To activate the TEMPERATURE LOCK, press the "MODE
" button in the
TOOLS
submenu until the
LOCK +
symbol is displayed on the screen. The
lock icon will flash on and off when deactivated. Press the "ON
" button to activate the TEMPERATURE LOCK feature.
When the TEMPERATURE LOCK is activated, the JETS, LIGHTS and any other features your hot tub may have will operate normally, and the temperature setting can be
viewed but can NOT be changed.
To deactivate the TEMPERATURE LOCK, press the "MODE
" button in the
TOOLS
submenu until the
LOCK -
symbol is displayed on the screen.
Press the "OFF
" button to deactivate the TEMPERATURE LOCK feature.
sPa lOCk
The SPA LOCK feature deactivates all of the functions of the control panel. It is generally used to prevent unwanted use of the spa. The SPA LOCK menu is a submenu
of the
TOOLS
menu.
To activate the SPA LOCK, press the "MODE
" button in the
TOOLS
submenu until the
SPA +
symbol is displayed on the screen. Press the "ON
" button to activate
the SPA LOCK feature.
When the SPA LOCK is activated, the buttons for the JETS, LIGHTS, temperature control, and any other features your spa may have are deactivated. To
deactivate the SPA LOCK, press the "MODE
" button in the
TOOLS
submenu until the
SPA -
symbol is displayed on the screen. Press the "OFF
"
button to deactivate the SPA LOCK feature.
lOCk OVerrIDe
The Lock Override feature is for spa users who normally keep the set temperature locked. Should the user wish to lock all spa controls temporarily, the spa lock can be
applied over an already-applied temperature lock. Then, when the spa lock is removed, the temperature lock will remain on to prevent unwanted tampering with the set
temperature.
suMMer MODe
Your Caldera
®
spa is equipped with a Summer Mode timer. The Summer Mode timer can be activated during extremely hot summer months if it becomes difficult to
maintain water temperatures low enough for comfort. When you turn on the Summer Mode timer, the heater will immediately shut down while the circulation pump (which
can add heat to the water through normal operation) will remain on for approximately 5 minutes for heater cool-down. Both the heater and circulation pump will remain
off for the next 8 hours. The summer mode icon on the main control panel will illuminate and remain illuminated for as long as the summer mode timer is on. Following
this 8-hour period, the circulation pump, heater, and ozone will continue to turn off for an 8-hour period every day that the Summer Mode timer is on. The continual 8-hour
shutdown minimizes the amount of heat transferred to the spa water. When the outside temperature begins to cool, the Summer Mode timer should be turned to the OFF
position (the summer mode icon on the main control panel turns off). This is the efficient 24-hour circulation mode that keeps the heater operation and operating costs to a
minimum during colder/heavier usage months.
NOTE
: Whenever power is disconnected, and then reconnected to the spa, the Summer Mode timer will reset starting with
the eight-hour shutdown mode. If a different eight-hour shut down time is desired, deactivate the Summer Mode, then reactivate at the beginning of the desired eight-hour
shut down time.
IMPORTANT
: The Summer Mode will not lower the spa’s water temperature below the ambient air temperature.
To activate the Summer Mode, follow these steps:
Set the temperature control to 80°F (26°C). On the control panel press the "MODE
1.
" button until the
TOOLS
menu is displayed. Then press
the "ON
" button to enter the
TOOLS
submenus. Press the "MODE
" button until the
STMR+
symbol is displayed on the screen. Press the "ON
" button to
activate the Summer Timer mode. The Summer Mode must be deactivated when cooler temperatures return. To do this, simply follow step 2.
To turn the Summer Mode off, press the "MODE
2.
" button until the
TOOLS
menu is displayed. Then press the "ON
" button to enter the
TOOLS
submenus
press the "MODE
" button until the
STMR-
symbol is displayed on the screen. Press the "OFF
"
button to deactivate.
Summary of Contents for paradise series
Page 1: ......
