background image

22

FAULT DESCRIPTION

ALERTS

POSSIBLE CAUSE OF FAULT

OPERATIONS TO BE PERFORMED

Domestic hot 

water is not 

heated

blinking 

mandata a punto fisso

impostazione temperatura di 

mandata

limite temperatura ritorno

alta/bassa temperatura

compensazione

intervento limite temperatura ritorno

climatica

  

icon

 primary circuit shut-off valves closed

open the valves

modulating valve actuator disconnected from valve body

reconnect actuator

modulating valve actuator faulty

call qualified personnel to have it replaced

DHW temperature probe cable inverted with heating probe

restore correct connection

presence of air in the system

vent the system

electronic regulator not working

call qualified personnel to have it replaced

valve obturator blocked in closed position

call qualified personnel to have it replaced

centralised system not working/cold

contact person in charge of system

error code 6 active

DHW temperature probe disconnected

reconnect probe

DHW temperature probe faulty

call qualified personnel to have it replaced

error code 80 active

incorrect wiring/no credit

check electrical connections/top up credit

fixed 

mandata a punto fisso

impostazione temperatura di 

mandata

limite temperatura ritorno

alta/bassa temperatura

compensazione

intervento limite temperatura ritorno

climatica

  

icon

DHW priority flow meter disconnected

reconnect flow meter

DHW priority flow meter faulty

call qualified personnel to have it replaced

icon 

mandata a punto fisso

impostazione temperatura di 

mandata

limite temperatura ritorno

alta/bassa temperatura

compensazione

intervento limite temperatura ritorno

climatica

 absent

DHW production not enabled

enable DHW production by means of HIU 

interface

display is off

electric supply cut off

restore HIU electric supply

protection fuse burnt out

call qualified personnel to have it replaced

The water is 

hot but does 

not reach 

the desired 

temperature

blinking 

mandata a punto fisso

impostazione temperatura di 

mandata

limite temperatura ritorno

alta/bassa temperatura

compensazione

intervento limite temperatura ritorno

climatica

  

icon

domestic water cycle temperature set point too low

increase set point

primary return temperature limitation intervention

change the return temperature set point/

disable the function

primary circuit strainer of the HIU clogged

call qualified personnel to have it serviced

exchanger partly clogged

call qualified personnel to have it serviced

modulating valve actuator faulty

call qualified personnel to have it replaced

DHW temperature probe cable inverted with heating probe

restore correct connection

excessive demand for DHW

decrease demand

electronic controller not working

call qualified personnel to have it replaced

centralised system temperature insufficient

contact person in charge of system

primary circuit flow rate insufficient

contact person in charge of system

primary flow rate limit too low

contact person in charge of system

Hot water 

temperature is 

too high

blinking 

mandata a punto fisso

impostazione temperatura di 

mandata

limite temperatura ritorno

alta/bassa temperatura

compensazione

intervento limite temperatura ritorno

climatica

  

icon

domestic water cycle temperature set point too high

decrease set point

DHW temperature probe cable inverted with heating probe

restore correct connection

modulating valve actuator faulty

call qualified personnel to have it replaced

valve obturator blocked in intermediate or open position

call qualified personnel to have it replaced

electronic regulator not working

call qualified personnel to have it replaced

primary circuit excessive flow rate due to DPCV valve 

malfunction

call qualified personnel to have it replaced

Antilegionella cycle in progress

contact person in charge of system

Hot water 

flow rate is 

insufficient

blinking 

mandata a punto fisso

impostazione temperatura di 

mandata

limite temperatura ritorno

alta/bassa temperatura

compensazione

intervento limite temperatura ritorno

climatica

 

icon

HIU strainer clogged

call qualified personnel to have it serviced

possible domestic water system shut-off valves 

partially closed

open the valves

insufficient pressure in centralised domestic water circuit

call qualified personnel to have it serviced

Hot water flow 

rate is zero

-

possible domestic water system shut-off valves closed

open the valves

no cold water in centralised domestic circuit

call qualified personnel to have it serviced

HIU strainer completely clogged

call qualified personnel to have it serviced

exchanger completely blocked

call qualified personnel to have it serviced

Troubleshooting

Summary of Contents for SATK22107

























Reviews: