background image

13

DHW function

   

 

 

 

 

 

 

   

 

 

 

 

 

 

   

 

 

 

 

 

 

   

 

 

 

 

 

 

DHW Comfort functions (pre-heating, DHW recirculation)

 

 

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

 

The DHW cycle always takes priority over the heating cycle.

DEFAULT SETTING: fixed DHW set point (parameter t06=0)

When DHW cycle activation is requested, due to DHW tapping by the
user  (detected  by  the  domestic  water  flow  meter),  the  regulator
modulates  the  valve  opening  in  order  to  adjust  the  temperature
detected by the domestic water probe to the selected set point value.
When tapping ends, the modulating valve is fully closed.
The DHW cycle ON condition is indicated by the blinking 

symbol.

OPTIONAL  SETTING:  primary  return  temperature  limit
(technical parameter t06 = 1)

When DHW cycle activation is requested, due to DHW tapping by the
user  (detected  by  the  domestic  water  flow  meter),  the  regulator
modulates  the  valve  opening  in  order  to  adjust  the  temperature
detected by the domestic water probe to the DHW set point value if
the  return  temperature  is  less  than  or  equal  to  the  set  limit.  If  this
condition is not met, the flow temperature is reduced (by a maximum
of 7°C down to a temperature that can be no less than 40°C), in order
to bring return temperature within the limit values. 

Due  to  the  activation  of  the  return  temperature  limitation
function, DHW temperature can be lower than the set value.

DHW/primary return limit temperature setting

To set the DHW temperature press the <SET> key until the symbol in
the red circle appears; for the return temperature limit press the key
until the symbols in the green circle are displayed. Use the <R> knob
to change the value (*).
The range of possible DHW temperatures is 42–60°C, while the range
of possible return temperatures is 15–45°C.

   

 

 

   

 

 

 

 

 

 

(*)  if  these  set  points  cannot  be  changed  you  must  set  parameter  t07  to  value  0  in  the  technical  menu  (see  “access  to  technical  menu”  below).
Parameter t07 = 1 “freezes” the operating set points to prevent inadvertent modifications by the user.

The comfort function can be, alternatively, preheating of the DHW plate
heat exchanger or management of DHW recirculation. They are enabled
by setting to ON or PROG the comfort function (see page 11).

DEFAULT  SETTING:  DHW  exchanger  preheating  function
(parameter t02 = 0)

During periods when the domestic water cycle is not used, if the DHW
probe detects a temperature 10°C below the SET value, the regulator
partially  opens  the  domestic  hot  water  modulating  valve  for  the  time
required (max. 5 min.) to bring the exchanger to the condition wherein it
can assure rapid DHW production.
The active pre-heating cycle is indicated by the blinking 

symbol.

This  function  is  of  lower  priority  than  any  domestic  water  or  heating
cycles.

OPTIONAL SETTING: management of DHW recirculation in the
apartment (parameter t02 = 1)

In alternative to the DHW comfort function it is possible to manage DHW
recirculation,  using  a  similar  logic.  During  periods  when  the  domestic
water cycle is not used, if the DHW probe detects a temperature 10°C
below the SET value, by means of an auxiliary microswitch (see page
19), the regulator closes the circuit supplying the circulation pump (not
supplied) generating a DHW cycle lasting for a pre-set amount of time.
This amount of time is pre-set to 2 minutes. It can be changed by acting
on parameter t09 on the technical menu (1 unit = 10 seconds).

The circulator has to be fed through the auxilliary microswitch so
that  the  control  of  recirculation  is  carried  out  by  the  heat
interface  unit. DHW  recirculation  (t02=1)  disables  the  other
functions operating on the auxilliary microswitch described on
page  16.  Refer  to  page  16  for  the  electrical  characteristics  of
the microswitch.

Both  comfort  functions  can  be  enabled  according  to  user  defined
weekly time programming. Refer to the remote user interface manual.

   

 

 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

 

N.B.:  In the presence of a DHW recirculation system a suitably
sized expansion vessel must be installed.

Summary of Contents for SATK32 Series

























Reviews: