background image

Safety and alarms

Safety thermostat cut-out 
Error code 69

HIUs  configured  to  support  low  temperature  heating  continuously
monitor the safety thermostat controlling the flow temperature.
If the safety thermostat is activated during a general cycle, the heating
circulation  pump  immediately  comes  to  a  stop  and  the  modulating
valve is completely closed. 
After  the  user  has  removed  the  block  imposed  by  the  safety
thermostat,  operation  can  only  be  re-enabled  when  the  modulating
valves are completely closed again.
This means that if a domestic water cycle is in progress, the activation
of the shut-off valve will be postponed until the end of that domestic
water cycle.

Corrective action

To restore the operating mode press the manual RESET button.

If  the  electronic  circuit  board  detects  a  fault,  the  display  shows  the
error code concerned and the symbol 

.

   

 

 

   

 

 

 

 

 

 

Corrective action

Normal operating conditions are restored automatically once the faulty
probe is working properly again (see page 20 - “Temperature probe
replacement”).

Probe fault

If  a  temperature  probe  fails,  the  associated  cycle  will  be  stopped
immediately and disabled.
Any  requests  to  run  cycles  not  associated  to  the  previous  one  will
continue to run normally.

Heating flow probe fault 
Error code: 5

Domestic hot water probe fault 
Error code: 6

Return probe fault
Error code: 15

The  HIU  is  disabled  due  to  an  incorrect  connection  on  the  circuit
board  front  terminals  or  due  to  an  input  from  an  external  device
indicating zero credit.                                                                          

Corrective action

                                                                             

Check the electrical connections or, in the case of zero credit, top-up
the external device/contact the service supplier.                                 

Heat interface unit disabled
Error code 80

Heating circuit pressure switch fault 
Error code 4

The  electronic  regulator  continuously  monitors  the  status  of  the
pressure  switch  controlling  the  water  pressure  in  the  heating  circuit.
If the pressure switch trips, the heating circulation pump immediately
comes  to  a  stop  and  the  modulating  valve  is  completely  closed.
This fault implies the stoppage of the heating cycle only.                    
Domestic water drawing requests will continue to be served normally.

N.B.

:  A  low  pre-charge  value  of  the  expansion  vessel  can  cause  a

pressure switch fault.

Corrective action

Return  to  the  operating  mode  is  subordinate  to  restoration  of  the
correct water pressure in the secondary heating circuit (see page 9 -
“Filling the user system”).

18

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

External temperature fault
Error code: 38

 

 

 

     

 

 

 

 

 

 

   

 

 

   

 

 

 

 

Summary of Contents for SATK32 Series

























Reviews: