background image

21

C

B

H

C

D

E

F

G

Cleaning the HIU primary circuit strainer

All heat interface units have a strainer on the inlet for water from the
centralised system.
To  clean  these  strainers,  carry  out  the  following  maintenance
procedure:
-   Unscrew the cap (B)
-   Remove the strainer mesh and discard any impurities it contains
-   Refit the strainer mesh
-   Refit the cap and tighten it.

Temperature probe replacement

-   Disconnect the probe cable by bending tab (C) slightly 

    and extracting the connector.

-   Unscrew the probe
-   Fit the new probe  
-   Reconnect  the  connector  respecting  the  only  possible  way  it  can

be inserted.

Replacing the actuator

-   Extract the fixing clip (D) and then the actuator
-   Position the new actuator (E)
-   Insert the fixing clip, respecting the correct direction
-   Reconnect the connector.

Replacing the valve obturator

-   Disconnect the valve actuator (see previous paragraph) 
-   Extract the obturator, unscrewing the locking nut (F)
-   Replace the obturator, screw on the locking nut (F) and then fit the

actuator

-   Insert the fixing clip, respecting the correct direction
-   Reconnect the connector.

Replacing the DHW priority flow meter

-   Disconnect the flow meter cable acting on the connector
-   Extract the flow sensor (G)
-   Position the new sensor
-   Reconnect  the  connector  respecting  the  only  possible  way  it  can

be inserted.

Replacing or cleaning the DHW priority flow meter turbine

-   Extract the flow sensor
-   Unscrew and remove the cartridge (H)
-   Remove any impurities or change the cartridge if necessary
-   Screw the cartridge back in
-   Reposition the flow sensor 

When  carrying  out  maintenance  on  the  electrical  part,  follow  the
indications on page 19 for the connections.
After  concluding  maintenance,  proceed  with  the  filling  and  checking
operations described in the chapter “commissioning” (page 9) and fit
the cover. 

If  you  require  any  information  regarding  spare  parts,  please  contact
Caleffi spa.

Summary of Contents for SATK32 Series

























Reviews: