background image

3

Customer Support: 1-866-409-4581

AiR COMPReSSOR

how to find a local service center:

even quality built equipment might need service or repair parts.

Contact the California Air Tools Customer Service department:
Phone: 1-866-409-4581
Online: WOWed.CALIFORNIAAIRTOOLS.COM

please provide the information below:

Model number and Serial number and specifications shown on the

Model number/Serial number plate.
Part number or numbers shown in the parts list section of the

owner’s manual for your air compressor model.
A brief description of the trouble with the air compressor.

do not return your air compressor for service or parts to the

store/dealer where purchased.

IMPORTANT SAFeTy

INSTRuCTIONS

Safety messages & Signal Words:

DANGER

DANGER

There is a danger of electric shock.

There is a danger of electric shock.

Use only undamaged electrical cords.

Use only undamaged electrical cords.

DO NOT touch bare wires or receptacles.

DO NOT touch bare wires or receptacles.

DO NOT operate air compressor in wet weather or in wet 

DO NOT operate air compressor in wet weather or in wet 
conditions.

conditions.

DO NOT touch air compressor or cords if hands or feet are 

DO NOT touch air compressor or cords if hands or feet are 
wet.

wet.

Ensure that all cords are free of damage before connecting 

Ensure that all cords are free of damage before connecting 
to the power supply.

to the power supply.

Ensure that you have a sufficient electrical supply for 

Ensure that you have a sufficient electrical supply for 
supporting the requirements of the motor.

supporting the requirements of the motor.

Improper installation of the grounding plug is able to result 

Improper installation of the grounding plug is able to result 
in a risk of electric shock. When repair or replacement of the 

in a risk of electric shock. When repair or replacement of the 
cord or plug is required, do not connect the grounding wire 

cord or plug is required, do not connect the grounding wire 
to either flat terminal. The wire with insulation having an 

to either flat terminal. The wire with insulation having an 
outer surface that is green with or without yellow stripes is 

outer surface that is green with or without yellow stripes is 
the grounding wire.

the grounding wire.

This product must be grounded. In the event of an electrical 

This product must be grounded. In the event of an electrical 
short circuit, grounding reduces the risk of electrical shock 

short circuit, grounding reduces the risk of electrical shock 
by providing an escape wire for the electric current. 

by providing an escape wire for the electric current. 

This product is equipped with a cord having a grounding 

This product is equipped with a cord having a grounding 
wire  with an appropriate grounding plug. The plug must be 

wire  with an appropriate grounding plug. The plug must be 
plugged into an outlet that is properly installed and 

plugged into an outlet that is properly installed and 
grounded in accordance with the local codes and 

grounded in accordance with the local codes and 
ordinances.

ordinances.

This product is for use on a nominal 220-V circuit and has a 

This product is for use on a nominal 220-V circuit and has a 
grounding plug similar to the plug illustrated in sketch A. 

grounding plug similar to the plug illustrated in sketch A. 
Only connect the product to an outlet having the same 

Only connect the product to an outlet having the same 
configuration as the plug.

configuration as the plug.

Do not use an adapter with this product.

Do not use an adapter with this product.

SHOCK

SHOCK

Summary of Contents for 20040DCADC

















Reviews: