California Instruments 2750L-P Series Instruction Manual Download

Page: 4 / 151

INSTRUCTIONAL MANUAL

2750L-P/4500L-P/6000L-P

August, 2001

Rev. K

-iv-

TABLE OF TABLES

Table 1-1:

OUTPUT VA PER PHASE ----------------------------------------------------------------------------------------------- 1

Table 1-2

SPECIFICATIONS 4500L-P / 2750L-P / 6000L-P------------------------------------------------------------------ 4

Table 2-1

MAXIMUM LENGTH OF OUTPUT WIRES ------------------------------------------------------------------------ 20

Table 3-1

POWER OUTPUT TERMINAL BLOCK (TB1)--------------------------------------------------------------------- 26

Table 3-2

EXTERNAL SENSE CONNECTOR (J6)---------------------------------------------------------------------------- 26

Table 3-3

SYSTEM INTERFACE CONNECTOR (J7) ------------------------------------------------------------------------ 28

Table 3-4

KEYPAD KEY DESCRIPTION ---------------------------------------------------------------------------------------- 32

Table 3-5

OUTPUT PARAMETER SCREEN ----------------------------------------------------------------------------------- 33

Table 3-6

MEASUREMENT SCREENS------------------------------------------------------------------------------------------ 34

Table 3-7

CALIBRATION SCREEN ----------------------------------------------------------------------------------------------- 34

Table 3-8

CONFIGURATION SCREENS ---------------------------------------------------------------------------------------- 35

Table 3-9

FRONT PANEL DISPLAY ERROR MESSAGES----------------------------------------------------------------- 44

Table 3-10

COMMONLY USED GPIB ABBREVIATIONS--------------------------------------------------------------------- 49

Table 3-11

UNIT ADDRESS GROUP ---------------------------------------------------------------------------------------------- 50

Table 3-12

PROGRAM HEADERS-------------------------------------------------------------------------------------------------- 54

Table 3-13

TLK ARGUMENTS------------------------------------------------------------------------------------------------------- 62

Table 3-14

EXAMPLE TALK RESPONSE (3-PHASE SYSTEM)------------------------------------------------------------ 64

Table 3-15

STATUS BYTE VALUES ----------------------------------------------------------------------------------------------- 67

Table 3-16

CHANNEL DESIGNATORS AND NOUN MODIFIERS --------------------------------------------------------- 71

Table 3-17

NON-CNF STATUS MESSAGES ------------------------------------------------------------------------------------ 76

Table 3-18

DISCRETE FAULT INTERRUPT CONDITIONS ----------------------------------------------------------------- 80

Table 3-19

SAMPLE PROGRAMMING STRINGS ------------------------------------------------------------------------------ 81

Table 4-1

SETUP LOAD VALUES------------------------------------------------------------------------------------------------- 86

Table 4-1

SETUP LOAD VALUES (continued) -------------------------------------------------------------------------------- 87

Table 4-2

AMPLIFIER LOAD BALANCE ADJUSTMENTS ------------------------------------------------------------------ 99

Table 4-3

CURRENT LIMIT ADJUSTMENT -----------------------------------------------------------------------------------102

Table 6-1

TROUBLESHOOTING -------------------------------------------------------------------------------------------------111

TABLE OF FIGURES

Figure 1-1

MODEL 4500L / 2750L / 6000L-P OUTPUT DRAWINGS-------------------------------------------------------- 2

Figure 2-1

6000L / 2750L and 4500L-3P REAR PANEL CONNECTIONS ----------------------------------------------- 14

Figure 2-2

SYSTEM INTERCONNECT ------------------------------------------------------------------------------------------- 15

Figure 2-2

SYSTEM INTERCONNECT FOR MODE OPTION -------------------------------------------------------------- 16

Figure 2-2

SYSTEM INTERCONNECT ------------------------------------------------------------------------------------------- 17

Figure 2-2

SYSTEM INTERCONNECT ------------------------------------------------------------------------------------------- 18

Figure 2-3

FUNCTION TEST SETUP---------------------------------------------------------------------------------------------- 23

Figure 3-1

FRONT PANEL CONTROLS AND INDICATORS---------------------------------------------------------------- 25

Figure 3-2

REAR PANEL CONNECTIONS - 6000L/2750L/4500L --------------------------------------------------------- 27

Figure 3-3

FUNCTION STROBE CONNECTIONS----------------------------------------------------------------------------- 31

Figure 3-4

KEYPAD -------------------------------------------------------------------------------------------------------------------- 31

Figure 3-5

REMOTE COMMEND SEQUENCES ------------------------------------------------------------------------------- 52

Figure 3-6

CIIL PROGRAM SYNTAX---------------------------------------------------------------------------------------------- 69

Figure 3-7

CONFIDENCE TEST FLOW DIAGRAM ---------------------------------------------------------------------------- 74

Figure 4-1

INTERNAL ADJUSTMENTS AND JUMPER LOCATIONS ---------------------------------------------------- 84

Figure 4-2

EQUIPMENT HOOKUP FOR PERIODIC CALIBRATION------------------------------------------------------ 90

Figure 4-3

FLOW DIAGRAM A REMOTE CALIBRATION-------------------------------------------------------------------- 94

Figure 4-3

FLOW CHART (continued)--------------------------------------------------------------------------------------------- 95

Figure 5-1

AC POWER SYSTEM BLOCK DIAGRAM ------------------------------------------------------------------------106

Figure 5-2

OSCILLATOR MODULE BLOCK DIAGRAM ---------------------------------------------------------------------108

Figure 6-1

MODULE LOCATION --------------------------------------------------------------------------------------------------115

Summary of Contents for 2750L-P Series























































































































































Search results

Summary of Contents for 2750L-P Series

Reviews:

Related manuals for 2750L-P Series

Brands by name

Popular brands

California Instruments 2750L-P Series, Instruction Manual

Search results

Summary of Contents for 2750L-P Series

Reviews:

Related manuals for 2750L-P Series

Brands by name

Popular brands