background image

Safety Instructions & Precautions

continued

SAVE THESE INSTRUCTIONS

ELECTRICAL HAZARD

• 

All Platinum systems are shipped from the factory wired for 220 Volts.

• To reduce risk of electrical shock make sure all power to pool equipment area is off prior 

to any installation or removal of Platinum System components.

• Immediately replace damaged Control Center cord.

• Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers 

and other equipment.

• Severe shock or injury will likely occur as a result of drill or drill cord coming in contact 

with water. Never allow electric drill or cord to come in contact with water. Only plug drill 

into a Class A (5 Millampere Trip) protected Ground Fault Circuit Interrupter (GFCI) in 

accordance with the National Electrical Code Section 680 (USA ONLY). Please see your 

drill owner’s manual for further safety precautions.

• Install the Control Center at least 10 feet from the inside walls of a pool to prevent any 

possibility of the unit coming in contact with water.

• The Platinum Chlorinator has been designed with an internal electronic flow sensing 

tab. This device automatically switches the power to the electrolytic cell “OFF” when the 

water through the cell stops. To prevent cell damage and/or personal injury, do not in any 

way interfere with this system which has been designed for your protection.

CHEMICAL USE HAZARD

• To avoid personal injury when working with pool chemicals, always wear rubber gloves 

and eye protection, and work in a well-ventilated area. Use caution when choosing a 

location to open and use chemicals as they may damage any surface to which they come 

in contact.

• The addition of certain chemicals can reduce the effectiveness of chlorine. Always make 

sure that proper residual chlorine levels are maintained to avoid personal injury.

• This product produces chlorine. Individuals with any type of chlorine sensitivity should   

take the appropriate precautions to avoid injury or illness.

Important Notice:

 

Attention Installer:

 This manual contains important information 

about the installation, operation and safe use of this product. Before installing this 

product, read and follow all warning notices and instructions which are included. This 

information should be given to the owner and/or operator of this equipment.

WARNING: IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO RISK OF FIRE, 

ELECTRIC SHOCK, OR INJURY TO PERSONS. READ AND FOLLOW ALL

INSTRUCTIONS. 

Failure to follow safety warnings and instructions can result in severe 

injury, death, or property damage. Call (888) 635-0330 or go to www.calimarpool.com for 

additional free copies of these instructions.

5

Summary of Contents for CMARSSG20-5


























Reviews: