IT
Pagina 6 / 88
I-MPC Rev1 - Istruzioni originali
avanzate accessibili da personale qualificato. Per
accedere a questo menù viene richiesta una password
(vedi paragrafo 7.6.).
Err – Ultimi 5 allarmi. Incaso di assenza di errore
appare nOnE.
AE - Tramite il menu AE si identifica il firmware
installato. Firmware=AE01+AE02+AE03
7.4. Parametri
Sono disponibili e programmabili i seguenti parametri:
7.4.1. UP – Impostazioni di funzionamento
Par.
Descrizione
Valore da inserire
Standard
UP01 Modalità di funzionamento FL = Portata costante
(Flow)
SP = Velocità costante
(Speed)
CL = Pulizia Rapida
(Quick Clean)
FL
UP02 Setpoint
1 ÷ 4
3
7.4.2. PP – Impostazioni di adescamento (Priming)
Par.
Descrizione
Valore da inserire
Standard
PP01 Gestione adescamento
(priming)
0 = check Adescamento
sempre attivo
1 = check Adescamento
sempre disattivo
2 = check Adescamento
disattivo per i primi
PP04 min
0
PP02 Tempo check per il quale deve
sussistere la condizione di mancato
adescamento prima che si attivi
la fase Adescamento (sec)
10 ÷ 120
30
PP03 Tempo massimo della
fase Adescamento (min)
1 ÷ 15
2
PP04 Tempo per il quale
viene disattivato il check
Adescamento (min)
(utilizzato solo se PP01=3)
1 ÷ 10
5
7.4.3. CL – Impostazioni modalità Pulizia Rapi-
da (Quick Clean)
Par.
Descrizione
Valore da inserire Standard
CL01 Tempo di attivazione
modalità Pulizia
Rapida (min)
1 ÷ 30
5
7.4.4. AP – impostazioni avanzate
Par.
Descrizione
Valore da inserire Standard
AP01
Reset impostazioni di
fabbrica
nO, yES
nO
7.5. Modalità di funzionamento
E’ possibile impostare tre diverse modalità di
funzionamento:
FL - FLOW (portata costante) (default) in questa
modalità il sistema è impostato per funzionare ad un
setpoint di portata definito tramite il parametro AP02
(vedi tab. 7.5.1)
SP – SPEED (velocità costante) in questa modalità il
sistema è impostato per funzionare ad un setpoint di
velocità definito tramite il parametro AP02 (vedi tab. 7.5.1)
CL – QUICK CLEAN (Pulizia Rapida) in questa modalità
il sistema è impostato per funzionare alla velocità
massima per un periodo di tempo definito dal parametro
CL01, successivamente la pompa si porta in OFF.
7.5.1. Tabella Setpoint
Setpoint
1
2
3
4
Modalità
portata
costante
(Flow)
1 ÷ 3
m
3
/h
3 ÷
7
m
3
/h
7 ÷
9
m
3
/h
9 ÷
12
m
3
/h
Modalità
Velocità
costante
(speed)
50 %
70 %
85 % 100 %
In modalità portata costante (Flow) il punto di lavoro
si sposta all'interno di un range di portata che dipende
dal setpoint impostato e dalle condizioni dell'impianto
(tab. 7.5.1)
Display
Modalità Pulizia Rapida
CL
Fase di adescamento
PrI
7.5.2. Gestione adescamento (Priming)
La procedura di adescamento consiste in due fasi.
1. Fase check Adescamento: la pompa, durante il
normale funzionamento, verifica se è completamente
adescata. Se PP01=0 la fase di check Adescamento
è sempre attiva. Questa fase può essere disabilitata
in modo permanente (PP01=1) oppure disabilitata
per un periodo di tempo limitato al termine del quale
viene riabilitata (PP01=2). Se PP01=2 il check
Adescamento viene disabilitato per primi PP04
minuti ogni qualvolta viene ri-alimentata la pompa.
2. Fase Adescamento: la pompa passa alla fase
Adescamento solo se durante la fase di check
Adescamento la pompa non è completamente
adescata per un periodo di tempo definito dal
parametro PP02. In questa fase la pompa lavora alla
massima velocità finché non risulta completamente
adescata o comunque fino al periodo di tempo
massimo definito da PP03. Al termine di questo
periodo di tempo se la pompa è completamente
adescata passa automaticamente al setpoint
impostato, altrimenti appare Er07.
7.6. Inserimento password
Quando si desidera entrare in un menù con PASSWORD,
lampeggia la cifra da digitare. Con i pulsanti (più) o
(meno) si varia la cifra lampeggiante. Con il pulsante
(enter) si conferma la cifra e si passa alla successiva.
Se tutte le cifre sono corrette si accede al MENÙ
altrimenti comincia a lampeggiare la prima cifra.
Per uscire dalla programmazione, premere (menù)
fino a quando non si ritorna ai parametri visualizzati,
quando si è usciti dalla modalità programmazione,
scompare l'indicatore di programmazione.
password: 1959
8. AVVIO E IMPIEGO
8.1. Controlli prima dell’accensione
L’apparecchio non deve essere messo infunzione in
presenza di parti danneggiate.
8.2. Primo avviamento
OFF
8.2.1. Riempimento
ATTENZIONE: evitare il funzionamento a secco.
Con la pompa sotto il livello d’acqua nella vasca
(funzionamento sotto battente), riempire la pompa