background image

7

V. Care and Maintenance

VI. Replacement Parts

Fig. 1

Fig. 2

Casters

Caster maintenance should be performed after every cleaning.
1.   Grease swivel raceway of caster using a lubricant such as Lubriplate #930-AA, 

Keystone #84EPXLT multi-purpose grease or equivalent. Apply grease using a 
grease gun with a needle nose adapter or a tube-type applicator such as 
Sta-lube Moly-graph Assembly Lube (Fig.1). These can be obtained at most 
auto parts stores.

2.   Use a light oil such as WD-40 on the hub (Fig.2). Check caster for damage 

and test caster spin and swivel rotation before returning to service.

Water Tanks 

Disconnect the outgoing line from tank and empty the tank. Wash out with a mild 
detergent using a soft brush and rinse with fresh water. Always empty the tank 
after using and store empty.

Stainless Steel Hand Sink Cart and Faucet 

Under ordinary conditions, light swabbing with soap or detergent, rinsing with 
clear water, and wiping with a cloth or dish towel should remove everyday dirt. 
Occasional scouring with a household cleanser is recommended. Remember to rub 
in the direction of the grain lines in the metal. 

Never use steel wool or sharp 

knives to clean your sink. 

The Hand Sink Cart is manufactured for hand washing 

capability, not for food preparation. If food is placed in the sink, please beware 
that some food, such as mustard, mayonnaise, lemon juice, vinegar, or salt are 
acidic or contain chlorides that will attack and corrode stainless steel if left in the 
sink for extended periods. 

Waste Water Tank 

Empty the tank and wash out with a mild detergent using a soft brush and rinse 
with fresh water. Always empty the tank after using and store empty.

Soap Dispenser 

Rinse out soap container with warm water. The dispenser handle should be cleaned 
daily with a clean wet cloth. Never use abrasive cleaners, detergents or steel wool.

TO ORDER REPLACEMENT PARTS: 

•  Call Cambro Customer Service at 800 833 3003 or 
•  Call International 714 848 1555
•  Fax your order to 714 842 3430 or
•  Call your local Cambro Representative or Distributor

Please visit www.cambro.com for a complete list of replacement parts. The 
model number of the Cambro CamKiosk

®

 Hand Sink Cart and/or heater is 

required to determine the correct replacement part. The cart model number can 
be found on the left side of the cart. Each heater has a label marked with heater 
serial and model number.

Summary of Contents for CamKiosk KSC402









Reviews: