CAME 001PSGD4, Installation Manual

P

age 

2

  - Manual code: 

1

1

9

G

3

2

6

5

119G3265

 ver

. 

2

  03/2014  © CAME cancelli automatici s.p.a. - The data and information pr

ovided in this manual ar

e subject to change at any ti

me without prior notice by CAME C

ancelli Automatici S.p.a.

ENGLISH

Foreword

• This product should only be used for the purpose for which it was explicitly 

designed. Any other use is considered improper and therefore dangerous. CAME 

Cancelli Automatici S.p.A. will not be held liable for damage caused by improper, 

incorrect or unreasonable use. • The safety of the product, and therefore its pro-

per installation, depends on total compliance with the technical specifi cations and 

installation procedures, as well as with rules regarding safety and use, expressly 

mentioned in the technical documentation for the products themselves. • Keep 

these warnings together with the installation and operation manuals for the ope-

rator system components.

Before installing

(preliminary check: in case of a negative outcome, do not proceed until you have 

complied with the safety requirements)

• Installation and testing must only be performed by qualifi ed personnel • Cable 

routing, installation, connection and testing must be carried out to the highest 

levels of workmanship in accordance with applicable laws and regulations • Be-

fore starting any operation, read all the instructions carefully; incorrect installation 

can be dangerous and harm persons or property • Check that the operator is in 

good mechanical condition, balanced and aligned, and that it opens and closes 

properly. If needed, also install suitable guards or use appropriate additional safety 

sensors • If the operator will be installed at a height of less than 2.5 m from the 

ground or other access level, check whether you will need any protections and/or 

warnings • Ensure that opening the turnstile does not create a dangerous situation 

• Do not mount the operator upside down or onto any elements that may fold 

under its weight. If needed, add suitable reinforcements at the points where it is 

secured • Do not install on ground that is not level • Check that any lawn watering 

devices will not wet the operator from the bottom up.

Installation

• Carefully section off  the entire site to prevent unauthorised access, especially by 

minors and children • Be careful when handling operators that weigh more than 

20 kg. In such cases, use proper weight handling safety equipment • CE safety 

devices (photocells, platforms, sensitive edges, emergency button etc.) must be 

installed in compliance with applicable legislation and according to the highest 

standards of workmanship, bearing in mind the environment, the type of service 

required and the operating forces applied to the moving turnstiles. Points where 

there is a risk of crushing, shearing or dragging must be protected using suitable 

sensors • End users must be informed of any residual risks by means of special 

pictograms as envisaged by legislation • All opening commands (buttons, key 

selectors, magnetic readers etc.) must be installed at least 1.85 m from the pe-

rimeter of the area of turnstile movement, or where they cannot be reached from 

outside through the turnstile. Also, the direct commands (buttons, touch comman-

ds etc.) must be installed at a height of at least 1.5 m and must not be accessible 

to the public • The turnstile identifi cation data must be clearly visible • Before 

connecting the turnstile to the power supply, make sure the identifi cation data 

corresponds to the mains data • The turnstile must be connected to an eff ective, 

compliant earthing system.

• The manufacturer disclaims any liability for the use of non-original products; this 

also results in the invalidation of the warranty • All ‘hold-to-run’ commands must 

be placed where the moving turnstile, transit areas and driveways are completely 

visible • Before delivery to the user, check that the system complies with the EN 

12453  and EN 12445 standards (impact tests), check that the operator has been 

properly adjusted and that the safety and protective devices work correctly • As 

appropriate and in a visible position, affi  x warning symbols.

Special instructions and advice for users

• Keep the turnstile’s area of operation clean and clear of any obstacles. Check 

that the photocells' area of operation is free from obstacles • Children must be 

supervised to make sure they do not play with the operator and the fi xed control 

CAUTION!

important personal safety instructions:

READ CAREFULLY!

Danger of hand crushing 

Danger - live parts

Warning Impact Hazard 

devices or stand in the turnstile's area of operation. Keep any remote control devi-

ces (i.e. transmitters) or any control devices away from children as well, to prevent 

the operator from being activated accidentally • The operator is not designed 

to be used by persons (including children) whose physical, sensorial or mental 

capacities are limited, or who are lacking in experience or knowledge, unless said 

persons can be supervised or given instructions regarding using the operator by a 

person responsible for their safety • Frequently check the system, to see whether 

any anomalies or signs of wear and tear appear on the moving parts, on the com-

ponent parts, on the securing points, on the cables and any accessible connec-

tions. Keep any joints lubricated and clean, and do the same where friction may 

occur • Perform functional tests on photocells every six months. Ensure that the 

glass on the photocells is kept clean (use a cloth slightly moistened with water; do 

not use solvents or any other chemicals as these could damage the devices) • If 

the system requires repairs or modifi cations, disconnect the power to the operator 

and do not use it until safety conditions have been restored • Cut off  the electrical 

power supply for manual opening. Read the instructions • If the power cable is 

damaged, it must be replaced by the manufacturer or the technical assistance 

service or by a person with a similar qualifi cation so as to prevent any risks • It is 

STRICTLY FORBIDDEN for users to perform OPERATIONS THEY ARE NOT EXPLI-

CITLY REQUIRED AND ASKED to do. For repairs, adjustments and extraordinary 

maintenance, CONTACT THE SPECIALIST TECHNICAL SERVICE CENTRE. On the 

periodic maintenance log, note down the checks you have done.

Further special instructions and advice for all

• Avoid working near the turnstiles or moving mechanical parts • Stay clear of the 

turnstile's area of operation when in motion • Do not resist the direction of move-

ment of the operator; this may present a safety hazard • At all times be extremely 

careful about dangerous points that must be indicated by proper pictograms and/

or black and yellow stripes • When using a selector or command in ‘hold-to-run’ 

mode, keep checking that there are no people in the area of operation of the 

moving parts. Do this until you release the command • The turnstile may move 

at any time without warning • Always cut the power when cleaning or performing 

maintenance.