background image

Pa

g

1

1

11

  - 

Ma

n

u

al

 cod

e: 

1

1

9

D

U

9

2

E

N

11

9

D

U

9

2

E

N

 ver

2

  

2  

01

/2

01

5

 © C

A

M

E S

.p.

A

. - 

T

h

e d

at

a a

n

d i

n

fo

rm

at

io

n r

ep

or

te

d i

n t

h

is

 in

st

al

la

ti

on

 m

an

u

al

 a

re s

u

sc

ep

ti

b

le t

o c

h

an

g

e a

t a

n

y t

im

e a

n

d w

it

h

ou

t o

b

lig

at

io

n o

n C

A

M

E S

.p.

A

. t

o n

ot

if

y u

se

rs

.

ENGLISH

7.2 Trouble shooting

MALFUNCTIONS

POSSIBLE CAUSES

CHECK AND REMEDIES

The gate will not open 
nor close

• There is no power
• The gearmotor is released
• The transmitter’s batteries are run down
• The transmitter is broken
• The stop button is either stuck or broken
• The opening/closing button  or the key selector are stuck

• Check that the power is up
• Call assistance
• Replace batteries
• Call assistance
• Call assistance
• Call assistance

The gate opens but 
will not close

• The photocells are engaged

• Check that photocells are clean 
and in good working order
• Call assistance

The flasher does not 
work

• The bulb is burnt

• Call assistance

8 Maintenance

Date

Notes

Signature

Periodic maintenance log for end-user (every 6 moths)

8.1 Extra-ordinary maintenance

           

The following table serves to note down any extraordinary maintenance, repairs or improvements performed by specialised firms. 

N.B.: Any extraordinary maintenance must be performed by specialised technicians.

Extra-ordinary maintenance log

Installer’s stamp

Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed _______________________________________________________________________________________
__________________________________________________________________________________________________
_

Installer’s stamp

Operator name

Date of job

Technician’s signature

Requester’s signature

Job performed _______________________________________________________________________________________
__________________________________________________________________________________________________
_

Summary of Contents for A 3024













Reviews: