background image

Page 

25

 - Manual 

FA02036-EN

  - 12/2023 - © C

AME S.p.A. - The contents of this manual may be changed at any time and without notice. - T

ranslation of the o

riginal instructions

Read data

Upload user data, timings and configurations to the memory device (memory roll).

 The function is displayed only when a USB stick is inserted into the USB port or when a memory roll card is inserted into the control board.

F51

0 =Deactivated (Default)
1 = Activated

Transferring MASTER-SLAVE parameters

Enable sharing for the parameters programmed on the master gate with the slave gate.

 This function appears only if the [RSE] function is active.

F52

OFF (Default)
ON

Opening direction

Set the gate opening direction.

F54

0 = To the left (default)
1 = To the right

CRP address

Assign a unique identification code (CRP address) to the control board. It is used where there are multiple operators connected via CRP.

F56

from 1 to 255

RSE speed

Set the remote connection system communication speed on the RSE port.

F63

0 = 1200 bps
1 = 2400 bps
2 = 4800 bps
3 = 9600 bps
4 = 14400 bps
5 = 19200 bps
6 = 38400 bps (default)
7 = 57600 bps
8 = 115200 bps

RIO ED T1

Associate one of the available functions with a wireless safety device.

F65

OFF (Default)
P0 = It stops the gate and excludes automatic closing. Use a control device to resume movement.
P7 = Reopen while closing.
P8 = Reclose while opening.

RIO ED T2

Associate one of the available functions with a wireless safety device.

F66

OFF (Default)
P0 = It stops the gate and excludes automatic closing. Use a control device to resume movement.
P7 = Reopen while closing.
P8 = Reclose while opening.

Summary of Contents for BXV06AGL

































Reviews: