CAME G2080E Installation And Operation Manual Download

Page: 53 / 128

- M

-E

- 0

18 - © C

e S

.p.

. - T

e m

's c

onte

nts m

ay b

e e

ite

d at a

ny ti

e w

ith

t n

oti

F30

Opening slow-down speed

15 = Minimum speed / … / 40 = Maximum speed.

Setting the boom opening slow-down speed, calculated as a percentage.

⚠

Warning: the speed parameter ﬁ elds vary according to the type of boom:

- for 2 m booms with a joint, set the slow-down speed percentage from 20 to 40;
- for 4 m booms, set the speed percentage from 20 to 30.
- for booms between 6 m and 8 m, set the slow-down speed percentage from 15 to 40.

F31

Closing slow-down speed

15 = Minimum speed / … / 40 = Maximum speed.

Setting the boom closing slow-down speed, calculated as a percentage.

⚠

Warning: the speed parameter ﬁ elds vary according to the type of boom:

- for 2 m booms with a joint, set the slow-down speed percentage from 20 to 40;
- for 4 m booms, set the speed percentage from 20 to 30.
- for 6 m booms, set the slow-down speed percentage from 15 to 30;
- for 8 m booms, set the slow-down speed percentage from 15 to 20.

F33 Calibration

speed

20 = 20% of travel (minimum) / … / 40 = 40% of travel (maximum)

Setting the boom travel automatic-calibration speed, calculated as a percentage

F34 Travel

sensitivity

10 = maximum sensitivity / … / 100 = minimum sensitivity(

default

)

Adjusting obstruction detection sensitivity during travel.

F35 Slow-down

sensitivity

10 = maximum sensitivity / … / 100 = minimum sensitivity(

default

)

Adjusting obstruction detection sensitivity during slow-down.

F37

Opening slow-down point

40 = 40% of travel/ … / 60 = 60% of travel

Adjusting the starting point of opening slow-down for the boom as a percentage of the total travel.
Warning! The percentage varies depending on the type of boom:
- for booms with a joint, between 2 m and 4 m, set the percentage from 40 to 60;
- for booms between 6 m and 8 m, set the percentage from 60 to 70.

F38

Closing slow-down point

20 = 20% of travel/ … / 75 = 75% of travel

Determining the starting point of closing slow-down, as a percentage of the total travel.
Warning! The percentage varies depending on the type of boom:
- for 2 m booms with a joint, set the speed percentage from 20 to 40;
- for 4 m booms, set the percentage from 40 to 60;
- for 6 m booms, set the percentage from 60 to 70;
- for 8 m booms, set the percentage from 65 to 75.

F49

Enabling serial connection

0 = Deactivated (

default

) / 1 = Paired/ 2 = Alternate

To enable paired or alternate operation.

F50 Save

data

0 = Deactivated (

default

) / 1 = Activated

To save users and system settings in the memory roll.



This function only appears if a memory roll has been inserted on the panel.

F51 Read

data

0 = Deactivated (

default

) / 1 = Activated

To load the data saved in the memory roll.



This function only appears if a memory roll has been inserted on the panel.

F52

Parameters transfer to paired/alternate mode

0 = Deactivated (

default

) / 1 = Activated

To load parameters from the MASTER barrier to the SLAVE barrier.



This function only appears if function F 49 is set to PAIRED or ALTERNATE operation.

F60 Sleep

mode

To reduce the energy consumption of the photocells in stand-by.

F61 Pre-fl

ashing

0 = during opening and closing (default) / 1 = only during closing / 2 = only during opening

After an opening or closing command is given, the ﬂ ashing light connected to 10-E1 ﬂ ashes before the barrier begins to move.
For information on adjusting the time, see function F 21.