background image

p. 

3

 - Manual 

FA01354-EN

  - 07/2019 - © C

AME S.p.A. - The cont

ents of this manual may change, at any time, and without notice. - Original instructions

GENERAL PRECAUTIONS FOR INSTALLERS

 Important safety instructions.

 Follow all of these instructions. Improper installation can cause serious bodily harm.

 Before continuing, also read the general precautions for users.

Use this product only for its specifically intended use. Any other use is hazardous. • The manufacturer can not be held 

liable for any damage caused by improper, unreasonable, and erroneous use. • This manual's product is defined by the 

Machinery Directive 2006/42/CE as partly-completed machinery. • Partly-completed machinery is an assembly that 

almost constitutes a machine, but which, alone, cannot ensure a clearly defined application. • Partly-completed machinery 

is only destined to be incorporated or assembled to other machinery or other partly-completed machinery or apparatuses 

to build machinery that is regulated by the Machinery Directive 2006/42/EC. • The final installation must comply with the 

Machinery Directive 2006/42/EC and the current European reference standards. • The manufacturer declines any liability 

for using non-original products; which would result in warranty loss. • All operations indicated in this manual must be 

carried out exclusively by skilled and qualified personnel and in full compliance with current regulations. • Laying of cables, 

installation and testing must follow state-of-the-art procedures as dictated by applicable standards and laws. • Make sure 

the mains power supply is disconnected during all installation procedures. • Check that the temperature ranges given and 

those of the location match. • Make sure that the opening automatic barrier does not constitute a hazard. • Do not install 

on slopes, that is, on any surfaces that are not perfectly level • If necessary, add suitable reinforcements to the anchoring 

points. If necessary, add suitable reinforcements to the anchoring points. • Make sure that the operator, in the installation 

place, does not get wet by direct jets of water (sprinklers, water cleaners, etc.). • Make sure you have set up a suitable 

dual pole cut off device along the power supply that is compliant with the installation rules. It should completely cut off the 

power supply according to category III surcharge conditions. • Demarcate properly the entire site to prevent unauthorized 

personnel to enter; especially children and minors. • In case of manual handling, have one person for every 20 kg that 

need hoisting; for non manual handling use proper hoisting equipment in safe conditions. • During the fixing phases, 

the operator could be unstable and overturn. Be careful and do not lean on it until it is fully fastened. • Use suitable 

protections to prevent any mechanical hazards due to persons loitering within the operating range of the operator. • The 

electric cables must pass through special pipes, ducts and cable glands in order to guarantee adequate protection against 

mechanical damage. • Make sure that the moving mechanical elements have adequate distance from the wiring made. • 

The electrical cables must not touch any parts that may overheat during use (such as the motor and the transformer). • All 

fixed controls must be clearly visible after installation, in position that the guided part is directly visible, but far away from 

moving parts. In the case of a maintained action command, this must be installed at a minimum height of 1.5 m from the 

ground and must not be accessible to the public. • When the passage width clearance is greater than 3 m, you must use a 

fixed rest for the boom to support it. • If not already present, apply a permanent tag, that describes how to use the manual 

release mechanism, close to the mechanism. • Make sure that the operator has been properly adjusted and that the safety 

and protection devices, and the manual release, are working properly. • Before turning over to the final user, check that 

the system complies with the harmonized standards and the essential requisites of Machinery Directive 2006/42/CE. • 

Any residual risks must be indicated clearly with proper signage affixed in visible areas. All of which must be explained 

to end users. • Fit, in plain sight, the machine's ID plate when the installation is complete. • If the power-supply cable is 

damaged, it must be immediately replaced by the manufacturer or by an authorized technical assistance center, or in any 

case, by qualified staff, to prevent any risk. • Keep this manual inside the technical folder along with the manuals of all the 

other devices used for your automation system. • Remember to hand over to the end users all the operating manuals of 

the products that make up the final machinery.

Summary of Contents for GARD PT Series

































Reviews: