CAME GGT40AGS Installation Manual Download | Manualshive

Page: 24 / 40

background image

P

age

24

- Manual

FA01383-EN

- 04/2021 - © C

AME S.p.A. - The contents of this manual may be changed at any time and without notice. - T

ranslation of the o

riginal instructions

CX input

Associate a function with the CX input.

F2

CX input

OFF (Default)
C1 = Reopen while closing (photocells)
C4 = Obstacle standby (photocells)
C5 = Immediate closure at the travel end during opening
C7 = Reopen while closing (sensitive edges)
C9 = Immediate closure at the travel end during opening with obstacle standby during
closure
C10 = Immediate closure during opening with obstacle standby during closure (NO
contact)
C11 = Immediate closure during opening with obstacle standby during closure (NC
contact)
C13 = Reopening during closure with immediate stop once the obstacle has been
removed, even with boom not in movement
r7 = Reopen while closing (sensitive edges with 8K2 resistor)

CY input

Associate a function with the CY input.

F3

CY input

OFF (Default)
C1 = Reopen while closing (photocells)
C4 = Obstacle standby (photocells)
C5 = Immediate closure at the travel end during opening
C7 = Reopen while closing (sensitive edges)
C9 = Immediate closure at the travel end during opening with obstacle standby during
closure
C10 = Immediate closure during opening with obstacle standby during closure (NO
contact)
C11 = Immediate closure during opening with obstacle standby during closure (NC
contact)
C13 = Reopening during closure with immediate stop once the obstacle has been
removed, even with boom not in movement
r7 = Reopen while closing (sensitive edges with 8K2 resistor)

CZ input

Associate a function with the CZ input.

F4

CZ input

OFF (Default)
C1 = Reopen while closing (photocells)
C4 = Obstacle standby (photocells)
C5 = Immediate closure at the travel end during opening
C7 = Reopen while closing (sensitive edges)
C9 = Immediate closure at the travel end during opening with obstacle standby during
closure
C10 = Immediate closure during opening with obstacle standby during closure (NO
contact)
C11 = Immediate closure during opening with obstacle standby during closure (NC
contact)
C13 = Reopening during closure with immediate stop once the obstacle has been
removed, even with boom not in movement
r7 = Reopen while closing (sensitive edges with 8K2 resistor)

«
...
22
23
24
25
26
...
»

Summary of Contents for GGT40AGS









































Reviews:

No comments

Related manuals for GGT40AGS

Brand: Balboa Instruments Pages: 10

Brand: Quantum Data Pages: 36

Brand: BEIER-Electronic Pages: 22

Brand: Jafar Pages: 9

Brand: Samsung Pages: 6

SyncMaster VC240

Brand: Samsung Pages: 39

Brand: Samsung Pages: 32

Brand: Samsung Pages: 91

Brand: Samsung Pages: 80

Brand: Radarcan Pages: 40

Brand: BADODOSECURITY Pages: 8

Brand: Jetline Pages: 58

Brand: QUALITY LIFTS Pages: 13

ACTIVE DRIVER M/M 1.1

Brand: DAB Pages: 10

Brand: d&b audiotechnik Pages: 3

ACTIVE DRIVER M/M 1.1

Brand: DAB PUMPS Pages: 38

Brand: Racal Instruments Pages: 94

Brand: Racal Instruments Pages: 97

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands