CAME PXIRVE, Manual

Pa

g.

 9

  -  

FA

00

502M

4A

  v.

 1 

 0

5/2

01

7  ©

Ca

m

e S

.p.

A.

ENGLISH

General Precautions

 Important people-safety instructions: READ CAREFULLY!

• Installing, programming, commissioning and maintenance 
must only be done by qualified, expert staff and in full com-
pliance with the applicable law. 
• Wear anti-static footwear and clothing when working on 
the control board.
• Keep these precautions. 
• This product should only be used for the purpose for which 
it was explicitly designed.

Description

PXIRVE is an outdoor dual PIR sensor, equipped with two 
independent heads that can be adjusted individually.
The sensor can operate in OR mode. It is then sufficient for 
one of the two heads to detect the alarm. In AND mode on the 
other hand, two detections are required in order to generate 
the alarm.
This sensor has been designed to operate in extremely 
bright environments. It is, however, necessary to prevent 
high intensity light sources from shining directly on or being 
reflected onto the sensor.
It is advisable to install the sensor in areas protected from 
the weather. 
To maintain the protection rating, it is mandatory to use the 
O-rings and screws supplied for installation.
Failure to observe the precautions listed above could 
result in malfunctioning of the product and in this case the 
manufacturer cannot be held liable. The sensor can detect the 
presence of animals.

Technical data

Type

PXIRVE

Power supply [V]

12

Current draw in standby [uA]

< 80

Current draw during alarm [mA]

< 24

Type

PXIRVE

Startup time [s]

30

Detection zones

10

Maximum range at 100° [m]

12

Assembly height [m]

0.8 to 2.5

Operating temperature [°C]

-40/+70

Relative humidity [%]

95

Weight [g]

410

Dimensions [mm]

190x85x113

Protection rating [IP]

54

Impact resistance [IK]

10

Functions 

A

LED

LED

Colour

Meaning

1

B 

DL1

Red

IR detection

3 

DL2

Blue

Alarm

Dip switch 

4

DEFAULT

DIP1 (Sensor logic)

ON

OR logic

 OFF

AND logic

DIP2 (IR sensitivity)

ON

Low sensitivity (for outdoor use)

 OFF

High sensitivity (for indoor use)

DIP3 (AND mode)

ON

DIRECTIONAL AND

Detection starts from the upper head and ends, within 
the AND time, with the detection of the lower head.

 OFF

NORMAL AND

Detection starts from one of the two heads and 
ends, within the AND time, with the detection of 
the other head.

DIP4 (Test)

ON  TEST mode

All the LEDs are enabled (JP4 closed) in test phase

 OFF

NORMAL operation (Test OFF) 

DIP5 (Anti-shading)

ON 

Enabled

 OFF

Disabled

DIP6 NOT USED

Jumpers

E

 JP4: 

Enable/Disable Buzzer (with DIP4 ON only)

JP4 OPEN: 

buzzer disabled

JP4 CLOSED: 

buzzer ena-

bled

6 

JP5: 

Enable/Disable Tear-Resistant Tamper

JP5 OPEN: 

tamper enabled

JP5 CLOSED: 

tamper disa-

bled

G 

JP6: 

Enable/Disable Anti-Opening Tamper

JP6 OPEN: 

tamper enabled

JP6 CLOSED: 

tamper disa-

bled

8 

JP7: 

Enabling/disabling alarm LED

JP7 OPEN: 

LED excluded

JP7 CLOSED: 

LED enabled

Trimmer

9

RV1

: adjusting the detection range of the upper head. Turn 

clockwise to increase the range.

J

RV2

: adjusting the detection range of the lower head. Turn 

clockwise to increase the range.