Pa
g
e
1717
- M
an
u
al
c
od
e
FA
0
0
13
5
-E
N
FA
0
0
13
5
-E
N
- ve
rs
.
22
- 0
1/2
0
17 - © C
am
e S
.p.
A
. -
The contents of this manual may be changed, at any time, and without notice.
OPEN-STOP from transmitter
Select the DIP switches as shown or press PROG on the
control board. The red LED flashes. Within ten seconds press
the button on the transmitter you wish to memorize.
Once memorized the buzzer sounds off for one second.
If the key has already been memorized, the LED will flash
quickly and buzzer will flash four times.
CLOSE-STOP from transmitter
Select the DIP switches as shown or press PROG on the
control board. The red LED flashes. Within ten seconds press
the button on the transmitter you wish to memorize.
Once memorized the buzzer sounds off for one second.
If the key has already been memorized, the LED will flash
quickly and buzzer will flash four times.
Transmitter activated OPEN-STOP-CLOSE-STOP
Select the DIP switches as shown or press PROG on the
control board. The red LED flashes. Within ten seconds press
the button on the transmitter you wish to memorize.
Once memorized the buzzer sounds off for one second.
If the key has already been memorized, the LED will flash
quickly and buzzer will flash four times.
Weather unit
⚠
The weather unit occupies 3 radio codes.
Select the DIP switches as shown or press PROG on the
control board. The red LED flashes. Within ten seconds press
the P2 key on the weather unit. Once memorized the buzzer
sounds off for one second.
If the weather unit has already been memorized, the LED will
flash quickly and the buzzer will sound off four times.
Deleting memorized transmitters and weather units
Select the DIP-switches as shown and press PROG on the
control board for five seconds.
After deleting, the red LED flashes and the buzzer sounds off
for one second.
Increasing the maneuvering speed
The default maneuvering speed is set to 70%.
To increase the maneuvering speed by 20%:
Select the DIP switches as shown or press PROG on the
control board. The red LED stays lit and buzzer sounds off
for one second.
To return to the default settings, press the PROG key again.
The LED flashes and the buzzer sounds off twice.
Reducing the slow-down speed
The default maneuvering speed is set to 50%.
To reduce the slow-down speed by 10%:
Select the DIP switches as shown or press PROG on the
control board. The LED stays on and the buzzer sounds off
for 1 s.
To return to the default settings, press the PROG key again.
The LED flashes and the buzzer sounds off twice.
Adjusting the sensitivity
The default obstruction-intervention time is one second.
To increase the intervention time to two seconds:
Select the DIP switches as shown or press PROG on the
control board. The LED stays on and the buzzer sounds off
for 1 s.
To return to the default parameters, press PROG again. The
LED flashes and the buzzer sounds off twice.
Slowed-down start when closing
The slow-down is disabled by default.
To enable it:
Select the DIP switches as shown or press PROG on the
control board. The LED stays on and the buzzer sounds off
for 1 s.
To return to the default parameters, press PROG again. The
LED flashes and the buzzer sounds off twice.
Immediate closing in case of a power outage
⚠
This function can be used only where there are batteries.
To enable it:
Select the DIP switches as shown or press PROG on the
control board. The LED stays on and the buzzer sounds off
for 1 s.
To return to the default parameters, press PROG again. The
LED flashes and the buzzer sounds off twice.
Resetting parameters
Once reset, the LED flashes and the buzzer sounds off twice.
With this function the transmitters and weather unit are not
deleted.
