background image

 

EMC_SPEC040_CLCR.doc 

Rev. E 

 2021 10 18 

25/63 

 

Install & Operating Manual 

CleanSeal V3

 

 

 

Rectangular Flange 
 

This flange form is available on many standard housings.  
May also be used as a custom feature on any housing.  
It is specifically suitable where integration space is at a premium. 

 

 

 

 

Use Ø 9 mm corner holes to position duct & gasket. 

 

Fasten with duct clamps on all 4 sides (not included). 

 

 

 

OR 

 

 

Fasten on corners using M5 bolts. 
 

PLEASE NOTE:

 

For most sizes, corner screws should be sufficient to achieve airtight connection. 

   

 

Depending on gasket hardness and the stiffness of the duct flange, additional  

   

 

duct clamps may be necessary on the long side. 

 

PLEASE NOTE:

 

Gasket material should be chose

n at customer’s discretion, depending on 

operating  

   

 

temperature and potential chemical aggression. 

 
   

 

For general purpose in Life Science, we recommend : 

 

Form gasket - closed-cell EPDM foam, type EPDM - ASTM D 1056 - 2 A2  -  4 mm. 
 
OR 
 

 

Strip gasket (adhesive), PE, type Lindab RJSM (or equivalent)  -  4 mm. 
 

Caution:

   

When using strip gasket material, take care to make clean, straight cuts and apply  

   

 

without gap to avoid flange leaks. 

 

 

Duct 

Housing 

Gasket 

Duct clamp 
(optional) 

 

 

 

 

 

 

 

 

 

8

 

M5

 

Summary of Contents for CleanSeal Exhaust V3
































































Reviews: