background image

WARRANTY

26

www.camltomlin.com

FLOW INSTALLATION - CORNER

LIMITED WARRANTY

If defects should occur despite our careful manufacture and strict quality control, please observe the following guarantee conditions: Please supply a copy of your purchase 

order and invoice number when reporting damage. These are prerequisites of the guarantee.

The guarantee claim does not lengthen the duration of the guarantee, which is always valid from the purchase date.  In case of defect or faulty product operation, please 

refer exclusively to your bathroom dealer.

CAML-TOMLIN IS NOT LIABLE

For damages due to improper installation.

For damages due to improper use

For damages due to the performance of unauthorized modifications or faulty repairs.

SCOPE OF GUARANTEE

CAML-TOMLIN covers defects in fabrication and materials; but does not cover the following:

transport damage, ordering errors, installation damage, operating and care errors, damage due to use of cosmetics & colouring liquids, differences in colours, surface 

imperfections necessary for manufacture, and parts subject to wear and tear.

CAML-TOMLIN reserves the right of repair or replacement. Installation and dismantling costs, including those by third parties, shall be accepted only when previously agreed 

in writing. Please return any shipments post unpaid to your supplier. Guarantee arrangements may follow after subsequent inspection by our quality control department.

5-YEAR GUARANTEE

On shower door and hardware while a 2 year warranty applies to the protective repellent film.  CAML-TOMLIN warrants acrylic units (shower base) to be free from defects in 

workmanship and materials under normal use and service for a period of five (5) years from the initial date of purchase by the owner/end-user, contractor or builder from an 

authorized dealer.

SAFETY

TEMPERED GLASS (10 MM). In the FLOW Shower Doors, special heat-treated safety glass is used, which is more impact, shock and temperature-resistant. If the glass 

breaks, glass granules form, reducing the danger of injury considerably.

IMPORTANT

Persons who are greatly limited in their freedom of movement should be supervised at all times by a qualified individual.

CARE & MAINTENANCE

IN ORDER FOR YOUR FLOW SHOWER DOORS TO KEEP ITS ATTRACTIVE LOOKS FOR MANY YEARS, PLEASE OBSERVE THE FOLLOWING CARE:

Rinse glass with clean water after showering. Remove water droplets with a squeegee or a soft cloth. For hygienic and easy cleaning of your Matrix product, we recommend 

biologically degradable cleansers. Regular care prevents stubborn stains and ensures a clean and hygienic surface for many years. Important: Do not under any 

circumstances use lime solvents or abrasive or corrosive cleansers. Otherwise the surfaces of the glass and hardware could be damaged. Use only cleansers specifically 

designed for chrome on chrome-plated parts.

LIMITATION

CAML-TOMLIN is not liable for incidental or consequential damage, loss of time, inconvenience, incidental expenses, labour, material charges or any other costs related to 

application of this warranty as it pertains to removal or replacement of defective merchandise.

This warranty shall not apply following incorrect operating procedures, breakage or damages caused by normal wear and tear, fault, carelessness, abuse, misuse, misapplica-

tion, improper maintenance, alteration or modification of the unit, as well as chemical or natural corrosion, accident, fire, flood, act of God or any other casualty. This warranty 

shall not apply to stain or malfunction caused by ferrous water, hard water or salty water.

The owner/end-user of the product covered by this warranty is entirely responsible for its proper installation. This warranty is void if unit is not tested prior to final enclosure 

as per the installation instructions. CAML-TOMLIN neither installs nor supervises the installation, nor hires a contractor for this purpose, and consequently cannot be held 

responsible for any defect, breakage or damage caused thereby or resulting thereof, either directly or indirectly. The owner/ end-user must provide access to the components 

of the product as described in the installation guide, so that CAML-TOMLIN can execute the warranty specified herein. If such access is not available, all expenses to provide 

said access will be the responsibility of the owner/end-user.

This warranty does not apply to products or equipment not installed or operated in accordance with instructions supplied by CAML-TOMLIN and all applicable rules, 

regulations and legislation pertaining to such installations.

CAML-TOMLIN reserves the right to discontinue products at any time or change specifications and/or design without notice and without incurring obligation. 

CAML-TOMLIN’s shower doors are guaranteed to fit with CAML-TOMLIN’s acrylic products but not necessarily with any other acrylic manufacturer’s product or custom tile 

applications.

EXCEPT AS OTHERWISE PROVIDED ABOVE, CAML-TOMLIN MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND 

FITNESS FOR A PARTICULAR PURPOSE OR COMPLIANCE WITH ANY CODE. In any case, CAML-TOMLIN cannot be liable for any amount over and above the purchase 

price paid for the product by the owner/end-user, contractor or builder. This warranty gives the owner/end-user specific legal rights. The owner/end-user may also have other 

rights which vary from one state and/or province to another.

In addition to the above conditions and limitations, the warranty period for products installed for commercial applications or used in commercial ventures is of one (1) year 

from the initial date of purchase by the owner/end-user, contractor or builder from an authorized dealer. CAML-TOMLIN is not responsible for loss of use or profit under any 

circumstances. If the product is sold by CAML-TOMLIN as a display, CAML-TOMLIN standard warranty applies.

Summary of Contents for FLOW48-2W




























Reviews: