Camlux PTI-403I User Manual Download

Page: 18 / 90

Quick Start of Network Connection

Network Setup -

Please follow the steps below to complete
the initial setup of the network function.

You will need to access a PC/laptop and should configure
that PC in order to communicate with the IP Camera.
Record the current TCP/IP properties of that PC. (IP address,
subnet mask, gateway, DNS, etc.d)

Please do not power on the IP Camera until instructed.

Temporarily disable any proxy servers configured in internet
Explorer.

If connecting the IP Camera directly to a modem, power down
and reset the modem. Leave the modem powered down until
configurations are finalized with the IP Camera and the IP Camera
has been correctly connected to the modem.

Change the IP address of that host PC to 192.168.1.11 and
subnet mask to 255.255.255.0 (leave all other entries blank)

Connect the IP Camera to your PC’s Ethernet port via the
supplied crossover cable. (It does not matter what end is
used for the PC)

Power on the IP Camera using the according to the power
rated.

After 1 minute of power, verify a flashing ACTIVE indicator,
and a flashing or solid LINK indicator. After the
corresponding indicator lights are properly displayed, open
Internet Explorer.

Type - http://192.168.1.80 (the default IP of the IP Camera)
into your address bar.

Default ID/Password to access IP Camera are both the
word:

admin.

Familiarize yourself with the Viewer Interface Screen.

Locate the TCP/IP configuration under Setup. Supply the
same ID and Password to enter Setup. (

admin

)

Under ‘Network Type’ select STATIC. You will only select
Dynamic if you are connecting the IP Camera directly to
your cable/DSL/Broadband modem and your Internet
Service Provider is supplying you a dynamic address.

10.

If your PC obtains its IP address automatically, then there is no
need to record any information.

If you have a network with other devices (such as PC/laptop, etc.)
or a router, you will NEVER select Dynamic.

Configure the IP Camera’s TCP/IP settings as you would any
other PC on your network, providing a proper IP address,
subnet mask, default gateway, and DNS server.

11.

If this is standalone unit with a direct connection to a cable/DSL/
Broadband modem then input the addresses you have received
from your ISP. If you received no IP address from your ISP, please
select Dynamic and choose the proper settings.

Current TCP/IP Settings

IP Address

Subnet Mask

Default Gateway

Primary DNS Server

Secondary DNS Server (Option)

Access your IP Camera via the Internet :

If you use a static IP address assigned by your ISP

1) Open Internet Explorer.
2) Type the IP of the IP Camera.
3) If you use a router, type the routers’ static IP and the web port
number of the IP Camera.

If you have a dynamic address provided by your ISP

1) Open Internet Explorer and visit the DDNS website.
2) Register the IP Camera.
3) Reboot the IP Camera.
4) Give the DDNS server 10 minutes to locate your IP Camera’s
IP information.
5) Click the refresh button in the Internet Explore.
6) After your camera is connected, select your camera.

15.

The IP Camera utilizes five TCP ports - a Web Port for utilizing
Internet Explorer, a Video Port, a Control Server Port, Audio
ports. A Web Port is for utilizing Internet Explorer, a Video
Server port is to support the streaming video, and a Control
Control Port is to transmit to control command. Also Audio
Port are to transmit and to receive Audio data. If this IP
Camera will be directly attached to a cable/DSL/Broadband
modem or has been assigned a static IP from your ISP, then
leave the default port settings.
If you are installing the IP Camera on a network, you must
define a Web Port other than 80. The other ports, a Video
Port, a Control Port, Audio Ports can remain unchanged.

If the IP Camera is connected to a network which utilizes a
router, you must have Port Forwarding configured on your
personal router to forward all ports to the IP address you
have assigned the IP Camera.

After configuring Port Forwarding on your router (if necessary),
you may then access your IP Camera on your local network
by opening Internet Explorer and specifying the IP address
and Web Server Port that you have assigned to the IP
Camera.

12.

13.

14.

Examples: http://192.168.0.200:8888

If you left your Web Port set to 80, then you don’t need to specify
the port in the Address Bar when accessing your IP Camera.