background image

CAMON Rotavators

Page 12 

PSR/AM/0912

Service Information

Every Week

• 

With the machine on a level surface, check the gearbox oil level, top up as necessary using the 

correct oil as listed below.  The gearbox oil level should reach between the two notches on the 

dipstick 

(fig. 2, C)

.

After the First 2 Weeks or 30 Hours of Work

• 

Replace the gearbox 

oil filter 

ONLY

(fig. 1, A),

 part number 58056249.

• 

Check the gearbox oil level using the dipstick 

(figs. 1 & 2, C)

, run the machine for 2-3 minutes 

and recheck gearbox oil level, top up as necessary using the correct oil as listed below.

Every 100 Hours of Work or 12 Months

• 

Change the gearbox oil by removing the gearbox drain plug 

(fig. 3, B)

.

•  Replace the gearbox oil filter 

(fig. 1, A),

 part number 58056249.

•  Clean the gearbox drain plug and refit.
• 

Fill gearbox using the correct oil and quantity as listed below.

•  Check the gearbox oil level, run the machine for 2-3 minutes and recheck gearbox oil level.

To replace the oil filter (fig. 1, A)

1.  Using the correct spanner, remove the 

filter.

2.  Smear a film of oil on the rubber gasket 

of the new filter.

3.  Mount  the  new  filter,  screwing  and 

tightening by hand only.

Fig. 1

A

C

Summary of Contents for C6





















Reviews: