background image

White

Black

Auger Motor

Blower Fan

 Burner

Controller

RTD Sensor

Power Cord

White

Red

White

Orange

White

Purple

Hot Rod 

MOLEX Connector

twice a year to determine when grease and or creosote buildup 
has occurred. When grease or creosote has accumulated, it should 
be removed to reduce risk of fire. Use a wire brush to clean the 
screen area of the chimney outlet on the inside of the grill with 
every 50 hours of use.

TROUBLESHOOTING

GRILL DOES NOT TURN ON.

Grill fails to turn on after switching the power button to the 
on position.
1.  Make sure the grill is plugged into a powered outlet. Check 

the circuit breaker and/or GFCI switch. Test the outlet using 
another appliance.

2.  Unplug the grill and check the fuse located in the front panel. If 

the fuse is blown replace only with 5.0 Amp 250V 5x20mm Slow 
Blow Fuse. Typical fuse marking will be T5AL250V. Make sure to 
confirm they are a slow blow fuse. Actual fuse dimensions are 
5.2x20mm.

    If problem cannot be resolved please call customer service.

GRILL DOES NOT HEAT UP OR DIGITAL READOUT DISPLAYS FLAME

1. Turn Power Off
2. Check hopper for pellets
3.  Check firebox to see if there are pellets in the firebox. The 

easiest way to do this is to pull the burner clean-out lever. 
Then remove the cup from the bottom of the grill and check for 
pellets. Use a vacuum to clean-out any pellets that may be in 
the bottom of the grill.

A.  If there are a lot of pellets in the cup. Reinstall the cup and 

close the burner clean-out, remove the grill grates, grease tray, 
and heat deflector and vacuum out any pellets in the bottom 
of the grill. Try restarting the grill. If restarting the grill does 
not work and pellets are getting to the burner cup the heating 
rodmay need to be replaced.

B.  If there are few or no pellets in the cup then turn the dial to the 

feed position and see if pellets fall out the bottom of the burner. 
If there are no pellets check to see if the auger is turning. If 
the auger motor is turning but the auger is not there may be 
a sheared auger pin. You can determine if the auger motor is 
turning by watching the small white fan at the end of the auger 
motor under the hopper. If the white fan is turning the auger 
motor is on. If the white fan is turning and the auger is not you 
will need to replace the auger pin. 

If problem cannot be resolved please call customer service.   

DIGITAL READOUT DISPLAYS SENSR

1. Turn the power off and unplug the grill.
2. Check to make sure the sensor inside of the grill is connected 
    properly to the electronic board under the hopper.
3. Call customer service for a replacement sensor.

DIGITAL READOUT DISPLAYS PRERR

1.  Press the Probe Temp button - Pressing the Probe Temp button 

will toggle the digital readout between the actual temperature 

inside of the grill and the temperature measured using the 
meat thermometer.   

2.  Make sure the meat thermometer is connected properly to 

the front of the grill. If the Probe Temp button is pressed to 
display the Probe Temp without the meat thermometer properly 
connected to the front of the grill it will display PRERR.

3. Call customer service for a replacement meat thermometer.

DIGITAL READOUT DISPLAYS “-----” 

1. Rotate the dial from Shutdown to feed or any other cook setting.

LIMITED WARRANTY

To activate warranty, register on-line at: www.CampChef.com

The manufacturer warrants stove components (except 
paint and finish) to be free from defect in materials and 
workmanship for 1 year from the date of purchase. All 
accessories (included with stove or purchased separately) 
are warranted from defect in materials and workmanship 
for 90 days from the original purchasing date. Within these 
periods, the manufacturer will replace or repair defective 
parts deemed unusable from its original intent by making 
available the parts thereof  
FOB Hyde Park, UT 84318

Product paint and finish is not warranted. The exterior finish 
of the product will wear down over time. 

Clean the unit after each use to maintain the finish and 
prolong the life of your product. Wipe away all grease and 
ashes. Keep metal products free of moisture, salts, acids 
and harsh fluctuations in temperatures.

Warranty does not cover normal wear of parts or damage 
caused by misuse, abuse, overheating and alteration. 
Repairs or alterations made by anyone other than Camp 
Chef are not covered in this Warranty. Manufacturer will 
not be held liable for any losses due to neglectful operation. 
Furthermore, this Warranty does not cover damaged caused 
by natural disasters such as earthquakes, hurricanes, 
tornadoes, floods, lightning, fires, etc. 

Upon the expiration of this warranty all such  liability will 
terminate. No other warranties are expressed or implied.

Keep all original sales receipts. Proof of purchase is 
required to obtain Warranty services. Prior written approval 
and a Return Authorization Number must be obtained and 
accepted for repair or replacement only. Returns must be 
shipped prepaid. Collect shipment or shipments without a 
Return Authorization Number will not be accepted.

To obtain Warranty services call 1.800.650.2433.
*Warranty applies to the contiguous  US states only.

Summary of Contents for SmokePro PG24DLX















Reviews: