5 - VERWENDUNG DES GERÄTES
58 - 112
ACHTUNG!
Ein Überdruck des Schalters (12) steigert die Schnittkraft nicht.
5.3 Batterieaufladung und Arbeitsweise des Batterieladegerätes
Was Batterieaufladung und Arbeitsweise des Batterieladegerätes betrifft, soll man das Handbuch des
Ladegerätes lesen.
5.4 Störung, Ursache und Behebung
ACHTUNG!
Alle Wartungseingriffe sollen von einem Wartungsmechaniker durchgeführt werden.
STÖRUNG
URSACHE
BEHEBUNG
Die Schere funktioniert nicht
Entladene Batterie (1)
Die Batterie (1) aufladen
Ausgeschaltete Batterie (1)
Die Batterie mittels des Schalters (8)
anschalten
Wähler (19) in Position OFF
Den Wähler gegen die Uhrzeigersinn
drehen
Ungespeiste elektronische Steuerung
Die Verbindung der elektronischen
Steuerung mit der Batterie kontrollieren
Ungespeiste Schere
Die Verbindung der elektronischen
Steuerung mit der Schere kontrollieren
Die Schere ist nicht stark genug
Entladene Batterie (1)
Die Batterie (1) aufladen
Verschlissene bewegliche Klinge (14)
Die Klinge (14) schärfen oder, wenn sie
zu verschlissen ist, ersetzen
Zu eng angeschraubter Klingenstift (29)
Die Funktion SERVICE durchführen
(Sehen Sie Abs. 5.1)
Batterie-Überverbrauch (1)
Verschlissene bewegliche Klinge (14)
Die Klinge (14) schärfen oder, wenn sie
zu verschlissen ist, ersetzen
Die Schere schließt die Klingen nicht
und der Bildschirm zeigt STOP gefolgt
von MAX_TEMP
Motorüberhitzung wegen des Schnittes
von zu dicken Ästen
Nicht mehr arbeiten, bis die Temperatur
ungefähr 5°C sinkt
Die Schere schließt die Klingen nicht
und der Bildschirm zeigt STOP gefolgt
von OVERLOAD
Scherenblockierung wegen innerer
Überhitzung
Einige Sekunden erwarten, ohne zu
arbeiten, und dann nur dünne Äste für
einige Minuten schneiden, um sich vom
Temperaturschutzwert zu entfernen
Die Schere schließt die Klingen nicht
und der Bildschirm zeigt STOP gefolgt
von STANDBY
Hebelblockierung
Den Hebel (12) dreimal drucken
Die Schere schließt die Klingen nicht
und der Bildschirm zeigt RESTART
Sicherheitsblockierung der Schere
Die Elektronikbox (19) mittels des
Wählers (19) wieder anlassen
Die Batterie schaltet sich nicht an/aus
Zu schnelle Druck auf den Schalter (8)
Den Schalter (8) einige Sekunden
gedrückt halten
6 - WARTUNG
6.1 Gewöhnliche Wartung
ACHTUNG!
•
Bevor man irgendeinen gewöhnlichen Wartungseingriff durchführt, soll man den Schalter (8) (Position
0) ausschalten.
•
Alle Wartungseingriffe, die nicht in diesen Bedienungsanleitungen beschrieben sind, sollen bei
autorisierten Campagnola-Kundendienststellen durchgeführt werden.
Die gewöhnlichen Wartungseingriffe können von den Bedienern durchgeführt werden.
Summary of Contents for COBRA
