6-Sp
Manual de Instrucciones
CHN103
Sujetadores
Estos sujetadores para acabado de Campbell Hausfeld los puede comprar en su tienda más cercana. Si necesita ayuda para
encontrar un artículo, comuníquese al 1-800-543-6400. Los sujetadores de Campbell Hausfeld cumplen o exceden el estándar
ASTM F1667
Cómo usar la
Herramienta
(Continuación)
Sujetadores y Repuestos
Use solamente sujetadores Campbell
Hausfeld originales calibre 18 (o su
equivalente) - (vea la información sobre
intercambio de sujetadores). El
desempeño de las herramientas, la
seguridad y la duración pueden
disminuir si no se utilizan los
sujetadores adecuados. Cuando ordene
piezas de repuesto o sujetadores,
especifique el número de la pieza.
!
ADVERTENCIA
Para reparar la herramienta
La herramienta deberá ser reparada
únicamente por personal calificado, y
deberán usar piezas de repuesto y
accesorios originales Campbell
Hausfeld, o piezas y accesorios que
funcionen de manera equivalente.
Para colocarle los sellos
Cada vez que repare una herramienta
deberá limpiarle y lubricarle las partes
internas. Le recomendamos que use
Parker O-lube o un lubricante equiva-
lente en todos los anillos en O. A cada
anillo en O se le debe dar un baño de
lubricante para anillos antes de instalar-
los. Igualmente, deberá ponerle un
poco de aceite a todas las piezas que se
mueven y muñones. Finalmente,
después de haberla ensamblado y antes
de probar la herramienta deberá pon-
erle unas cuantas gotas de aceite sin
detergente 30W u otro aceite similar,
en las líneas de aire.
Recommended Hookup
Quick
Plug
Quick
Coupler
Air
Hose
Quick Plug
(Optional)
Quick
Coupler
(Optional)
Regulator
Filter
3
General Safety
Information
(Continued)
Always assume the tool contains
fasteners. Respect the tool as a
working implement; no horseplay.
Always keep others at a safe dis-
tance from the work area in case of
accidental discharge of fasteners.
Do not point the tool toward your-
self or anyone whether it contains
fasteners or not. Accidental trigger-
ing of the tool could result in death
or serious personal injury.
Do not drive a fas-
tener on top of
other fasteners.
The fastener could
glance and cause
death or a serious
puncture wound.
Do not operate
or allow anyone
else to operate
the tool if any
warnings or
warning labels
are not legible.
Warnings or warning labels are locat-
ed on the tool magazine and body.
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution indicates
a potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate
injury.
Do not make any modifications to the
tool without first obtaining written
approval from Campbell Hausfeld. Do
!
CAUTION
used, manual lubrication through the
air inlet is
not
required on a daily basis.
The work surface
can become dam-
aged by excessive lubrication. Proper
lubrication is the owner’s responsibility.
Failure to lubricate the tool properly will
dramatically shorten the life of the tool
and void your warranty.
1. Disconnect the
air supply from
the tool to add
lubricant.
2. Turn the tool so
the air inlet is fac-
ing up. Place 4-5
drops of 30 W non-
detergent oil into
air inlet. Do not use
detergent oils, oil
additives, or air-
tool oils. Air tool oils contain sol-
vents which will damage the tool's
internal components.
3. After adding oil,
run tool briefly.
Wipe off any
excess oil from the
cap exhaust.
RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the tool.
1. The air com-
pressor must be
able to main-
tain a mini-
mum of 60 psi
when the tool is being used. An
inadequate air supply can cause a
loss of power and inconsistent
driving.
NOTICE
not use the tool if any shields or
guards are removed or altered. Do
not use the tool as a hammer.
Personal injury or tool
damage may occur.
Avoid long extended periods of
work with the tool. Stop using the
tool if you feel pain in hands or
arms.
Always check that the Work Contact
Element (WCE) is operating proper-
ly. A fastener could accidentally be
driven if the WCE is not working
properly. Personal injury may occur
(See "Checking the Work Contact
Element" Section).
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the tool. Personal injury
may occur.
Notice indicates
important infor-
mation, that if not followed, MAY
cause damage to equipment.
Avoid using the tool when the mag-
azine is empty. Accelerated wear on
the tool may occur.
Clean and check all air supply hoses
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
Operating The
Stapler
LUBRICATION
This tool requires lubrication before
using the tool for the first time and
before each use. If an inline oiler is
NOTICE
CHN103
Operating Instructions
www.chpower.com
!
WARNING
OIL
OIL
60 psi
Min.
100 psi
Max.
Lubricator
Información de intercambio
Las grapas usadas con la grapadora para acabado CHN103 también se pueden usar con las grapadoras : Senco LN4450, SJS-LR,
SKS L11-15, Hitachi N3804A, Duofast BN-1832S, KN-1848, ST-18, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, y Porter
Cable NS100.
Calibre
Fusión de
Grapas
Grapas
Modelo #
Longitud
de la grapa Corona
Punta
Acabado
la linea
por linea por caja
FN158K00
12,7 mm (1/2”)
Calibre 18 6,4mm (1/4") Cincel
Galvanizado/Cubierta por vinilo
Adhesivo
100
5000
FN168K00
15,9 mm (5/8”)
Calibre 18 6,4mm (1/4") Cincel
Galvanizado/Cubierta por vinilo
Adhesivo
100
5000
FN208K00
19,1 mm (3/4”)
Calibre 18 6,4mm (1/4") Cincel
Galvanizado/Cubierta por vinilo
Adhesivo
100
5000
FN258K00
25,4 mm (1”)
Calibre 18 6,4mm (1/4") Cincel
Galvanizado/Cubierta por vinilo
Adhesivo
100
5000
FN180615AV
12,7 mm (1/2”)
Calibre 18 6,4mm (1/4") Cincel
Galvanizado/Cubierta por vinilo
Adhesivo
100
1000
FN180620AV
19,1 mm (3/4”)
Calibre 18 6,4mm (1/4") Cincel
Galvanizado/Cubierta por vinilo
Adhesivo
100
1000
FN180625AV
25,4 mm (1”)
Calibre 18 6,4mm (1/4") Cincel
Galvanizado/Cubierta por vinilo
Adhesivo
100
1000
FN180630AV 3,18 cm (1-1/4”)
Calibre 18 6,4mm (1/4") Cincel
Galvanizado/Cubierta por vinilo
Adhesivo
100
1000
