Campbell Hausfeld CHN10610 Operating Instructions Manual Download

Page: 5 / 24

CHN10610

www.chpower.com

operating instructions

(Continued)

3 . Always use air supply hoses with a

minimum working pressure rating
equal to or greater than the pressure
from the power source if a regulator
fails, or 150 psi, whichever is greater .
Use 1/4 in . air hose for runs up to 50
ft . Use 3/8 in . air hoses for 50 ft . run
or longer . For better performance,
install a 3/8 in . quick plug (1/4 in . NPT
threads) with an inside diameter of
.315 in . (8mm) on the tool and a 3/8
in . quick coupler on the air hose .

4 . Use a pressure regulator on the

compressor, with an operating
pressure of 0 psi - 125 psi . A pressure
regulator is required to control
the operating pressure of the tool
between 60 psi and 100 psi .

opEraTioNal MoDE

Always know the

operational mode of

the tool before using. Failure to know
the operational mode could result in
death or serious personal injury.

TriGGEr oNlY MoDE (WiTH
TriGGEr loCK)

The tool is a single-actuator device . This
mode requires that, with the trigger
lock not positioned in the safe mode,
only a pull of the trigger will fire a
fastener .
After verifying there are no fasteners
in the tool, safety check the operation
of the activated trigger lock to prevent
the tool from firing a fastener before
storage . Always disconnect from
compressed air when not in use .

loaDiNG/UNloaDiNG THE Tool

1 . Always

disconnect

the tool from

the air supply

before loading

fasteners .

2 . Turn stapler upside

down and pull the
latch . Pull back on the
magazine cover .

3 . Insert a stick of

Arrow

T50

staples

or equivalent (see
Fastener Section) into the magazine
with the crown side down . Make
sure the staples are not dirty or
damaged .

4 . Push the magazine

cover forward until
the latch catches .

5 . Always unload all

fasteners before
removing tool from
service . Unloading
is the reverse of
loading, except always disconnect
the air hose before unloading .

aDJUSTiNG THE DirECTioN of THE
EXHaUST

The tool is
equipped with
an adjustable
direction exhaust
deflector . This is intended to allow the
user to change the direction of the
exhaust . Simply twist the deflector to
any direction desired .

ClEariNG a JaM froM THE Tool

1 . Disconnect the air

supply from the tool .

2 . Remove all fasteners from the

magazine (see "Loading/ Unloading
The Tool") .

3 . With the magazine open, remove

the jammed fastener, using pliers, a
screwdriver or a pick if required .

4 . Close magazine .

User-Maintenance

instructions

TECHNiCal SErviCE

Please call our Tool Hotline at 1-800-
543-6400 with any questions regarding
the operation or repair of this tool or
for additional copies of this manual .

faSTENEr aND rEplaCEMENT
parTS

Use only Arrow

T50

or equivalent staples.

Tool performance, safety and durability
could be reduced if improper fasteners
are used. When ordering replacement
parts or fasteners, specify by part
number.

Tool rEpair

Only qualified personnel should repair
the tool and they should use genuine
Campbell Hausfeld replacement parts
and accessories, or parts and accessories
which perform equivalently .

aSSEMblY proCEDUrE for SEalS

When repairing a tool, the internal parts
must be cleaned and lubricated . Parker
O-lube or equivalent must be used on
all o-rings . Each o-ring must be coated
with O-lube before assembling . A small
amount of oil must be used on all moving
surfaces and pivots . After reassembling,
a few drops of 30W non-detergent oil or
equivalent, must be added through the
air line before testing .

SToraGE

The stapler should be stored in a cool
dry place .

fasteners

Fasteners used in this stapler include:

• Arrow

T50

staples or any

equivalent fastener with the
approximate dimensions illustrated
below .

150 psi or greater

3/8 inch I .D .

rotate

10 .7 mm