background image

IN740800AV  9/12

© 2012 Campbell Hausfeld/Scott Fetzer

For parts, product & service information visit 

www.campbellhausfeld.com

Model: Cl154000AV

Description

An air reciprocating saw is a versatile tool for cutting a variety of materials such as 
sheet metal, wood, plastics, and fiberglass.

Unpacking

After unpacking the unit, inspect carefully for any damage that may have occurred 
during transit. Make sure to tighten fittings, bolts, etc., before putting unit into service.

Read & Follow all InstRuctIons

save these InstRuctIons 

do not dIscaRd

Safety Guidelines

This manual contains information that is very important to know and understand. This 
information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To 
help recognize this information, observe the following symbols.

 

Danger indicates an imminently hazardous situation which, if 

  not avoided, WILL result in death or serious injury.

 

Warning indicates a potentially hazardous situation which, if not 

  avoided, COULD result in death or serious injury.

 

Caution indicates a potentially hazardous situation which, if not 

  avoided, MAY result in minor or moderate injury.

 

Notice indicates important information, that if not followed, may 

  cause damage to equipment.

NOTE:

 Information that requires special attention.

General Safety Information

calIFoRnIa pRoposItIon 65

 

This product or its power cord may contain chemicals, including 

  lead, known to the State of California to cause cancer and birth 

defects or other reproductive harm. Wash hands after handling. 
 

You can create dust when you cut, sand, drill or grind  

  materials such as wood, paint, metal, concrete, 

cement, or other masonry. This dust often contains chemicals known to 
cause cancer, birth defects, or other reproductive harm. Wear protective 

gear.

Operating Instructions

Air Reciprocating Saw

Summary of Contents for CL154000AV

































Reviews: