background image

entangled in moving components,
causing equipment damage and or
personal injury.

9. Keep all persons away from parts

that move or become hot during
operation.

10. Be sure all powered devices are shut

off prior to connecting them to the
generator.

11. Keep the generator clean and well

maintained at all times.

Never operate this 
generator in an
explosive atmosphere
or poorly ventilated
area.

!

WARNING

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or
property damage! Retain instructions for future reference.

IN951300AV  2/00

Operating Instructions

Models GN301502AC and GN30C502AC

Generators

BUILT TO LAST

TM

These generators are powered by air-
cooled four cycle engines and designed
to run at maximum RPM and give a
continuous wattage as rated. 

When unpacking, inspect carefully for
any damage that may have occurred
during transit. Make sure any loose
fittings, bolts, etc., are tightened before
putting unit into service.

1. Before starting or

servicing any
generator, read and
understand all
instructions. Failure
to follow safety
precautions or instructions can cause
equipment damage and/or serious
personal injury. Engine instructions
for these units are contained in a
separate manual. Retain all manuals
for future reference.

2. Never use this generator for any

application other than that specified
by the manufacturer. Never operate
this generator under conditions not
approved by the manufacturer.
Never attempt to modify this
generator to perform in any manner
not intended by the manufacturer.

3. For maintenance and repairs, use

only products and parts
recommended by the manufacturer.

4. Be sure that the generator is

properly grounded to an external
ground path prior to operation.
Refer to the section entitled

“Grounding Instructions” for proper
grounding procedures.

5. Be sure that the generator is

operated only by persons who have
read and understand these
instructions.

6. Be sure that the generator is placed

on a flat level surface prior to and
during operation. The generator
must not slide or shift during
operation.

7. Keep all persons away from the

generator during operation.

8. Do not allow persons wearing loose

clothing or jewelry to start or
operate the generator. Loose
clothing or jewelry may become

MANUAL

Fig. 1 - Assembled Units GN301502AC and GN30C502AC

For parts, product & service information

visit 

www.campbellhausfeld.com

or call 

1-800-803-1436

© 2000 Campbell Hausfeld / Scott Fetzer

Description

Unpacking

General Safety

Summary of Contents for GN301502AC

























Reviews: