background image

Limited Warranty

1 .  DURATION: From the date of purchase by the original purchaser as follows: Three Years .
2 .  WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive,  

Harrison, Ohio, 45030, Telephone: (800) 543-6400

3 .  WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld 

compressor .

4 .  WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This VT6366 Campbell Hausfeld air compressor .
5 .  WHAT IS COVERED UNDER THIS WARRANTY: Parts and Labor to remedy substantial defects due to material and workmanship during 

the first year of ownership with the exceptions noted below . Parts only to remedy substantial defects due to material and workmanship 
during remaining term of coverage with exceptions noted below .

6 .  WHAT IS NOT COVERED UNDER THIS WARRANTY: 

A .  Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE 

OF ORIGINAL PURCHASE AS STATED IN THE DURATION . If the compressor is used for commercial, industrial or rental purposes, the 
warranty will apply for ninety (90) days from the date of purchase . Two-stage compressors are not limited to a ninety (90) day warranty 
when used in commercial or industrial applications . Some States do not allow limitations on how long an implied warranty lasts, so the 
above limitations may not apply to you

B .  ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, 

OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT . Some States do not allow the exclusion or limitations of incidental or 
consequential damages, so the above limitation or exclusion may not apply to you .

C .  Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with instructions 

provided in the owner’s manual(s) supplied with compressor .

D .  Pre-delivery service, e .g . assembly, oil or lubricants, and adjustment .
E .  Items or service that is normally required to maintain the product, e .g . lubricants, filters and gaskets, etc .
F .  Gasoline engines and components are expressly excluded from coverage under this limited warranty . The Purchaser must comply with 

the warranty given by the engine manufacturer which is supplied with the product

G .  Additional items not covered under this warranty:

1 . Excluded items pertaining to All Compressors
  a .  Any component damaged in shipment or any failure caused by installing or operating unit under conditions not in accordance  

  with installation and operation guidelines or damaged by contact with tools or surroundings .

  b . Pump or valve failure caused by rain, excessive humidity, corrosive environments or other contaminants .
  c .  Cosmetic defects that do not interfere with compressor functionality .
  d . Rusted tanks, including but not limited to rust due to improper drainage or corrosive environments .
  e .  The following components are considered normal wear items and are not covered after the first year of ownership . Electric  

  motor, check valve, pressure switch, regulator, pressure gauges, hose, tubing, pipe, fittings and couplers, screws, nuts,  
  hardware items, belts, pulleys, flywheel, air filter and housing, gaskets, seals, oil leaks, air leaks, oil consumption or usage,  
  piston rings .

  f .  Tank drain valves .
  g . Damage due to incorrect voltage or improper wiring .
  h . Other items not listed but considered general wear parts .
  i .  Pressure switches, air governors, load/unload devices, throttle control devices and safety valves modified from factory settings .
  j .  Damage from inadequate filter maintenance .
  k .  Induction motors operated with electricity produced by a generator .
2 . Excluded items specific to Lubricated Compressors:
  a .  Pump wear or valve damage caused by using oil not specified .
  b . Pump wear or damage caused by any oil contamination .
  c .  Pump wear or damage caused by failure to follow proper oil maintenance guidelines, operation below proper oil level or  

  operation without oil .

H .  Labor, service call, or transportation charges after the first year of ownership of stationary compressors . Stationary compressors are 

defined as not including a handle or wheels .

7 .  RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, compressor or component which is 

defective, has malfunctioned and/or failed to conform within the duration of the specific warranty period .

8 .  RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A .  Provide dated proof of purchase and maintenance records .
B .  Call Campbell Hausfeld (800-543-6400) to obtain your warranty service options . Freight costs must be borne by the purchaser .
C .  Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s) . 
D .  Repairs requiring overtime, weekend rates, or anything beyond the standard manufacturer warranty repair labor reimbursement rate .
E .  Time required for any security checks, safety training, or similar for service personnel to gain access to facility .
F .  Location of unit must have adequate clearance for service personnel to perform repairs and easily accessible .

9 .  WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be scheduled and 

serviced according to the normal work flow at the servicing location, and depending on the availability of replacement parts .

This Limited Warranty applies in the U .S ., Canada and Mexico only and gives you specific legal rights . You may also have other rights which 
vary from State to State or country to country .

10

www .chpower .com

Operating Instructions

Summary of Contents for VT636600

































Reviews: