background image

Installation Manual 

4.2.2  Installing the Standard Sensors 

Install all the sensors, carefully following the instructions and wiring diagrams 
given below. If you need further advice on the installation and operation of 
specific sensors, please read the installation manual provided for that sensor. 
Handle all sensors and wiring with care. Rough handling can damage both the 
mechanical and electrical integrity of the sensors. 

CS215 Temperature/Relative Humidity Probe 

The CS215 is fully integrated into the T351-RS Radiation Shield on the underside 
of the enclosure and wired into the datalogger before despatch.  

The sensor can be removed for periodic inspection/maintenance from inside the 
enclosure. Loosen the large gland nut retaining the CS215 and gently pull upwards 
on the threaded part of the sensor until it is completely removed. Do NOT pull the 
sensor up by the cable, as you may damage it. Replace the sensor by re-inserting it 
into the radiation shield through the gland until the threaded portion of the sensor 
is about 3mm above the main gland body. Re-tighten the gland nut. 

Wind Sentry Wind Speed and Direction Sensors 

Figure 4  Wind Sentry Mounting 

The 0300

2

-5 Wind Sentry is provided with a mounting bracket which fits directly 

to a 26.9mm outside diameter (3/4'' nominal bore) pipe. The mounting device 
consists of a two-piece male/female spigot, and is fitted with two band clamps. The 
lower ‘orientation’ clamp secures the equipment to the mast. By loosening the 
upper clamp, the complete bracket and sensors can be removed for maintenance, 
and, by means of the spigot, replaced in exactly the same orientation, saving the 
time and effort required in re-aligning the wind sensor to true north (see below). 

Mount and align the Wind Sentry as follows (refer to Figure 4, above): 

1. Ensure that the upper band clamp is fully tightened.

2. Open the lower ‘orientation’ clamp sufficiently so that the complete assembly

will easily slide onto the top of the mast.

3. Mount the complete Wind Sentry onto the top of the mast; only lightly tighten

the lower band clamp so that the assembly can be easily rotated.

26.9mm diameter (3/4” bore pipe) - to fit 
Wind Sentry

 

Both cables taken to junction box 
(not shown) on Wind Sentry arm

 

620mm max.

 

Two band clamps

 

220mm

 

‘Orientation’ ring

 

Special two-piece 
mounting device

 

Summary of Contents for BWS-200













































Reviews: