background image

Installation Manual 

13 

options which you can add to your BWS200 are outlined below. Note that all will 
require additional software running in both the logger and the PC.  

5.2.1  Short Haul Modem 

Campbell Scientific is able to provide a Short Haul point to point communications 
package with modems for either end of a fixed line cable to be supplied by the 
customer. Distances up to 25km are possible via this method. This popular option 
can be bought as a complete package and installed by the user.  

5.2.2  Multidrop Communications 

As the name implies Multidrop communications allows a number of weather 
stations to sit on the same data bus. For example a number of weather stations 
located around a farm might all be connected together in a ring, star or line 
formation onto the same cable. Campbell Scientific’s MD485 interfaces will direct 
the communications to the appropriate station. 

5.2.3  Radio Communications 

Short range radio communications are also possible but would require and 
alternative logger and so must be specified before ordering or will require your 
unit to be returned for upgrade.  

Note that all of the above options will require additional software either in the 
logger and/or in the PC. The cordless methods in particular will also have a major 
impact on the power budget of the unit and steps will need to be taken to minimise 
power loss. Please contact Campbell Scientific for more details and advice. 

The following communications connections require either PC400 or LoggerNet software: 

5.2.4  PSTN Telephone Connection 

Where your weather station has access to a fixed line telephone connection you 
can add a COM200E telephone modem and dial the logger up from your PC.  

5.2.5  GSM/GPRS Modem 

To connect via the GSM mobile network you will need a CS-GSM/GPRS kit 
including a GSM modem, antenna and connection leads. A Data SIM card should 
be obtained from your local authorised reseller. Refer to the manual. 

5.2.6  Internet Access 

To access your data via an Ethernet connection kit you will need a configured 
NL201 network module. 

6.  Final Installation Details 

1.

 

Secure all grounding wire and sensor cables to the mast (if used) or other 
suitable place.  

 

Summary of Contents for BWS-200













































Reviews: