Campbell CR3000 Micrologger Operator'S Manual Download | Manualshive

Page: 311 / 644

background image

Section 7. Installation

311

7.7.18.5.2

Serial I/O Input Programming Basics

Applications with the purpose of receiving data from another device usually
include the following procedures. Other procedures may be required depending on
the application.

1. Know what the sensor supports and exactly what the data are. Most sensors

work well with TTL voltage levels and RS-232 logic. Some things to
consider:

o

Become thoroughly familiar with the data to be captured.

o

Can the sensor be polled?

o

Does the sensor send data on its own schedule?

o

Are there markers at the beginning or end of data? Markers are very
useful for identifying a variable length record.

o

Does the record have a delimiter character such as a comma, space,
or tab? Delimiters are useful for parsing the received serial string
into usable numbers.

o

Will the sensor be sending multiple data strings? Multiple strings
usually require filtering before parsing.

o

How fast will data be sent to the CR3000?

o

Is power consumption critical?

o

Does the sensor compute a checksum? Which type? A checksum is
useful to test for data corruption.

2. Open a serial port with SerialOpen().

o

Example:

SerialOpen(Com1,9600,0,0,10000)

o

Designate the correct port in CRBasic.

o

Correctly wire the device to the CR3000.

o

Match the port baud rate to the baud rate of the device in CRBasic
(use a fixed baud rate — rather than autobaud — when possible).

3. Receive serial data as a string with SerialIn() or SerialInRecord().

—

Example:

SerialInRecord

(Com2,SerialInString,42,0,35,"",01)

o

Declare the string variable large enough to accept the string.

«
...
309
310
311
312
313
...
»

Summary of Contents for CR3000 Micrologger





































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CR3000 Micrologger

Brand: Nivus Pages: 60

Brand: AEMC instruments Pages: 36

Brand: ThermoWorks Pages: 12

Brand: INFRA-E-MOTION Pages: 15

SmartSystem SHIP L

Brand: berlinger Pages: 26

Brand: berlinger Pages: 40

Brand: Extech Instruments Pages: 39

Brand: YDOC Pages: 134

Brand: OfiTE Pages: 25

Brand: ICP DAS USA Pages: 75

Brand: Xylem Pages: 8

Brand: Omega Pages: 16

Brand: Omni Instruments Pages: 9

Brand: Lambrecht Pages: 12

myDatalogNANO Ex

Brand: Microtronics Pages: 111

Brand: American Thermal Instruments Pages: 10

Brand: Relay Pages: 8

Brand: Relay Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands