Campbell CR800 Series Operator'S Manual Download

Page: 356 / 598

Section 8. Operation

356

Ac Noise Rejection on Large Signals

Restated, when the CR800 is programmed to use the half-cycle 50 Hz or 60 Hz rejection techniques, a sensor does

not see a continuous excitation of the length entered as the settling time before the second measurement — if the

settling time entered is greater than one-half cycle. This causes a truncated second excitation. Depending on the

sensor used, a truncated second excitation may cause measurement errors.

Signal Settling Time

Settling time allows an analog voltage signal to settle closer to the true magnitude

prior to measurement. To minimize measurement error, signal settling is needed

when a signal has been affected by one or more of the following:

•

A small transient originating from the internal multiplexing that connects

a CR800 terminal with measurement circuitry

•

A relatively large transient induced by an adjacent excitation conductor

on the signal conductor, if present,because of capacitive coupling during

a bridge measurement

•

Dielectric absorption. 50 Hz or 60 Hz integrations require a relatively

long reset time of the internal integration capacitor before the next

measurement.

The rate at which the signal settles is determined by the input settling time

constant, which is a function of both the source resistance and fixed-input

capacitance (3.3 nfd) of the CR800.

Rise and decay waveforms are exponential. Figure

Input Voltage Rise and

Transient Decay

(p. 319)

shows rising and decaying waveforms settling closer to the

true signal magnitude, V

. The

SettlingTime

parameter of an analog

measurement instruction allows tailoring of measurement instruction settling

times with 100 µs resolution up to 50000 µs.

Programmed settling time is a function of arguments placed in the

SettlingTime

and

Integ

parameters of a measurement instruction. Argument combinations and

resulting settling times are listed in table

CRBasic Measurement Settling Times

(p.

319).

Default settling times (those resulting when

SettlingTime

) provide

sufficient settling in most cases. Additional settling time is often programmed

when measuring high-resistance (high-impedance) sensors or when sensors

connect to the input terminals by long leads.

Measurement time of a given instruction increases with increasing settling time.

For example, a 1 ms increase in settling time for a bridge instruction with input

reversal and excitation reversal results in a 4 ms increase in time for the CR800 to

perform the instruction.

Summary of Contents for CR800 Series























































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CR800 Series

Reviews:

Related manuals for CR800 Series

Brands by name

Popular brands

Campbell CR800 Series, Operator'S Manual

Search results

Summary of Contents for CR800 Series

Reviews:

Related manuals for CR800 Series

Brands by name

Popular brands