background image

Limited Warranty 

“Products manufactured by CSI are warranted by CSI to be free from defects in 

materials and workmanship under normal use and service for twelve months 

from the date of shipment unless otherwise specified in the corresponding 

product manual. (Product manuals are available for review online at 

www.campbellsci.com

.) Products not manufactured by CSI, but that are resold 

by CSI, are warranted only to the limits extended by the original manufacturer. 

Batteries, fine-wire thermocouples, desiccant, and other consumables have no 

warranty. CSI’s obligation under this warranty is limited to repairing or 

replacing (at CSI’s option) defective Products, which shall be the sole and 

exclusive remedy under this warranty. The Customer assumes all costs of 

removing, reinstalling, and shipping defective Products to CSI. CSI will return 

such Products by surface carrier prepaid within the continental United States of 

America. To all other locations, CSI will return such Products best way CIP 

(port of entry) per Incoterms ® 2010. This warranty shall not apply to any 

Products which have been subjected to modification, misuse, neglect, improper 

service, accidents of nature, or shipping damage. This warranty is in lieu of all 

other warranties, expressed or implied. The warranty for installation services 

performed by CSI such as programming to customer specifications, electrical 

connections to Products manufactured by CSI, and Product specific training, is 

part of CSI's product warranty. 

CSI EXPRESSLY DISCLAIMS AND 

EXCLUDES ANY IMPLIED WARRANTIES OF MERCHANTABILITY 

OR FITNESS FOR A PARTICULAR PURPOSE

CSI hereby disclaims, 

to the fullest extent allowed by applicable law, any and all warranties and 

conditions with respect to the Products, whether express, implied or 

statutory, other than those expressly provided herein.

” 

 

 

Summary of Contents for LI200RX





























Reviews: