1
5
4
3
2
1
2
Main Menu
[1/2]
1.Discharge
2.Depth Calibration
3.View Data
Discharge Measuring
1.Settings
2.Name:ILLER5
3.Party:SB&FR
4.Notes
5.START
Discharge
[1/3]
1.Load...
2.Near Edge
3.Far Edge
4.Verticals
5.Rod Offsets
1.Measure Method
2 Points
2.Using MID-section
Discharge
[2/3]
Discharge
[3/3]
1.Averaging:30
2.Salinity:0
Near Edge
1.Position : 0.00
2.Depth : 1.00
3.Roughness: 0.70
4.Stream width:10.00
Far Edge
1.Position :10.00
2.Depth :1.00
3.Roughness: 0.70
4.Stream width:10.00
Verticals
1.First pos. :1.00
2.Spacing :1.00
3.Measure Order:
Buttom to Surface
Rod Offsets
1.Sensor offset:0.02
2.Point offset:0.04
Load...
1.Load settings only
2.Continue a
previous
measurement.
Select File
1:IllER1 08:24 03/03
2:ILLER2 14:10 10/04
3:ROTTACH 10:45 11/04
4:DURACH 16:00 02/05
5:ACH 07:50 04/05
Step 2: Making basic settings to the discharge measurement
Press key 1.
Press key 2 and enter file name (max. 8 characters, no spaces or special symbols).
Press key 3 and enter party.
Press key 4 and add notes if wanted.
Press key 1
➝
Discharge menu [1/3] opens.
2a: There are not yet any basic settings at the station
Press key 2, 3, 4 or 5 and
set the respective parameters
(see below).
Press
■
key
➝
next menu level.
Press
key
➝
Return to Discharge measuring menu.
Press key 1 and select the
measure method.
Press key 2 and select the
type of evaluation.
Press
■
key
➝
next menu level.
Press key 1 and change
the measuring time if necessary.
Press key 2 and change
the salinity if necessary.
Press key 1 and enter position.
Reference point = near edge
➝
set to 0.
Reference point
≠
near edge
➝
set position > 0 (distance of the near edge from the cross-section zero point).
Press key 2 and enter depth.
Rectangular cross-section
➝
set depth > 0.
.
Natural rivers
➝
set to 0.
Press key 3 and enter roughness of the side wall (relevant with rectangular cross-section).
Press key 4 and enter stream width.
Press key 1 and enter position.
Set position > 0 (distance of far edge from zero point of cross-section).
Press key 2 and enter depth.
Rectangular cross-section
➝
set depth > 0.
.
Natural rivers
➝
set to 0.
Press key 3 and enter roughness of the side wall (relevant with rectangular cross-section).
Press key 4 and enter stream width.
Press key 1 and enter position of the first vertical.
Press key 2 and enter the spacing of the verticals.
Press key 3 and select the order of measurement: "Surface to Bottom";
"Bottom to Surface" or "Alternating".
Press key 1 and enter sensor offset
(distance of the symmetry axis of the sensor to the base plate of the measuring rod).
Press key 2 and enter point offset.
(distance of base plate of the measuring rod to the bed of the waterway).
2b: There are already basic settings at the station
Press key 1 in the Discharge Measuring menu (see above).
Press key 1 or 2.
Select file with its basic settings.
If point 1 in the Load… menu has been selected:
Press
key
➝
return to Discharge Measuring menu.
If point 2 in the Load… menu has been selected:
Press
key 3 times
➝
change to the measuring mode;
Continue measurement with another measuring point.