- 9 -
-16-
Keep young children away from the
appliance, some parts can be very hot.
ATTENTION: the appliance must be
completely unfolded and assembled, even
for the stove function.
CAUTION: Do not place a pan or any other
container above the
Toaster Grill.
When lighting a burner (stove or Toaster
Grill) with the piezoelectric, position the
burner adjustment knob on the maximum
flow rate position (
).
A pictogram specifies the position of each
adjustment knob on the appliance front
panel.
When the Grill
Toaster is in use the
temperature of the support on which the
appliance is placed can become high. The
appliance must not be placed on a
combustible surface (plastic, cloth, etc.). It
is recommended that is should be placed
on a surface that resists heat (concrete,
stone, brick, directly on the ground) or that
a good incombustible thermal insulator
should be positioned between the
appliance and its support.
Setting up
- Pull the lid closure hook, then open it.
-
Remove the toaster handle stored in the
pan support.
-
Fit the handle onto the grill accessory (the
ends of the wires must pass into the holes
in the grill)
(
fig. E
).
-
Check that the pan supports are correctly
positioned (
fig. F
).
-
Check that the gas supply pipe is not
trapped under the product and that it is
positioned so that it is not subject to
mechanical stresses (torsion, sharp parts of
furniture…)
-
Position the grill accessory in its location
after having assembled its handle (
fig. G
).
Your appliance is ready to use.
Stove function
- Open the gas supply (valve or lever on
regulator).
-
Rotate the knob corresponding to the
burner anti-clockwise to the maximum flow
rate position (
).
-
Wait 2 to 3 seconds and press the
piezoelectric button ( ) several times until
the burner lights. If it does not light after 3
tries, position the adjusting knob to "OFF"
(
) by rotating it clockwise. Wait 1 minute
before repeating the operation.
-
Adjust the flame to the container
dimension by positioning the knob to the
defined range between (
) and ( ).
- In strong winds arrange the appliance so
that the lid provides an obstacle to the
wind. Furthermore, your appliance has a
new patented, high wind performance
Campingaz
®
"
xcelerate burner
"
combined with a pan support (patented)
playing the role of 360° windshield.
-
When cooking is finished turn the knob
corresponding to the burner clockwise to
position (
).
Toaster Grill function
Important: do not close the lid when
using the Toaster Grill.
- Open the gas supply (valve or lever on
regulator).
-
Rotate the knob corresponding to the
burner anti-clockwise to the maximum flow
rate position (
).
-
Wait 2 to 3 seconds and press the
piezoelectric button ( ) several times until
GB
-17-
the burner lights. If it does not light after 3
tries, position the adjusting knob to "OFF"
(
) by rotating it clockwise. Wait 1 minute
before repeating the operation.
When cooking is finished turn the knob
corresponding to the burner clockwise to
position (
).
IMPORTANT: Never close the appliance
lid without checking that all the burners
are off, the valves closed and the
appliance has cooled down.
G - REMOVING OR CHANGING THE
GAS CYLINDER
- Check that the gas cylinder valve or
regulator lever is in the closed position.
- Place the adjusting knobs in position
(
) by turning them clockwise.
- Disconnect the regulator from the gas
cylinder.
- Install the new gas cylinder.
- Connect the regulator to the new gas
cylinder (check the condition of the
regulator seal, before connecting it to the
gas cylinder).
H -
FOLDING THE APPLIANCE
FOR TRANSPORT
IMPORTANT: Start by removing the gas
cylinder, and check that all the valves are
in the (
) position and that the appliance
has completely cooled down.
600 ST model only
-
Remove the textile shelf by withdrawing the
4 hooks. Fold the metal frames and roll the
textile around the frames.
-
Turn the appliance over and rest it on its lid.
-
Unscrew the 4 feet.
-
Fix the rolled textile shelf to the 2 "velcro"
attachments situated under the stove body.
-
Put the 4 feet back under the body,
proceeding in the reverse order to
assembly.
I - STORAGE - SERVICING
a) Appliance
Ensure that your stove is regularly
maintained, and it will give you many years
of excellent service.
- Do not clean the stove while it is in
operation. Wait for it to cool down, to avoid
burning yourself on the hot parts (hotplates,
pan supports, burners).
-
Remove the grill hotplates, the water
compartment, and drain the water (Grill
function).
- Check that the burner Venturi tubes on the
injector are not obstructed by dust or
cobwebs.
- While cleaning, take care not to obstruct
the burner holes. If the holes should be
blocked, for example by food overflow,
leave the burner cap in warm water and
unclog the holes using a non-metallic
brush.
- Clean the greasy parts with soapy water
or a non-abrasive detergent (do not use a
scouring pad or abrasive products).
-
For easier cleaning the grill hotplates,
water tank and pan supports can be
washed in a dishwasher.
- Remove and clean all parts of the stove
and dry them well.
-
"
600 ST
" model only: the shelves and
telescopic feet will be stored under the
appliance with the fixings provided for this.
-
Remember to protect the appliance lid by
inserting a protective material (paper,
cardboard, ….) between the lid and the grill
hotplates.
-
Store the assembly in a clean well
ventilated place.
-
If the appliance has not been used for
over 30 days verify that there are no
spider's webs blocking the burner tube,
which can reduce the efficiency of the
appliance or cause dangerous combustion
of gas outside the burner.
- Store the packed stove in a dry, well-
ventilated place.
GB
