background image

-

 

If the cooker hood is supplied with a lower chimney piece that must be 

fixed to the hood body with screws, remove the anti-grease filters from 

the hood by acting on the relevant handles (Fig.12). Then screw the lower 

chimney piece pipe to the inside of the hood, using screws 

P

(Fig.13). 

Re-locate the filters in their seat. 

USE AND MAINTENANCE 

• 

It is recommended to operate the appliance prior to cooking. 

It is recommended to leave the appliance in operation for  15 minutes after 

cooking is terminated in order to completely eliminate cooking vapours and 

odours. 

The proper function of the cooker hood is conditioned by  the regularity of 

the maintenance operations, in particular, the active carbon filter. 

 

• 

The anti-grease filters capture the grease particles suspended in the air, and 

are therefore subject to clogging according to the frequency of the use of the 

appliance. 

In order to prevent fire hazard, it is recommendable to  clean the filter at a 

maximum of 2 months by carrying out the following instructions: 

-  Remove the filters from the cooker hood and wash them  in a solution of 

water and neutral liquid detergent, leaving to soak. 

- Rinse thoroughly with warm water and leave to dry. 

- The filters may also be washed in the dishwasher. 

The aluminum panels may alter in color  after several  washes. This is not 

cause for customer complaint nor replacement of panels. 

 

• 

The active carbon filters purify the air that is replaced in the environment. 

The filters are not washable nor reuseable and must be replaced at maximum 

Summary of Contents for KI590TSL

















Reviews: