background image

10

SM2755 

INSTALLING THE WASHING  MACHINE

USING THE WASHING  MACHINE

RECOMMENDATIONS PRIOR TO USE

Warning: Before carrying out the fi rst wash, allow the washing 
machine to effect a short wash cycle without any washing.

This will allow the operation of the washing machine to be checked 

and will clean the drum.

Before each wash make sure that:

 

the water connections are correct, the drain hose is properly positioned (see 

connecting to the water supply) and that the water supply valve is open. 

 

with dry hands, insert the plug in the mains socket.

 

sort the wash into types of fabric (refer to clothing care symbols).

 

check that there are no objects left in any of the pockets of the items to wash, 

as these may damage the washing, the appliance or the fi lter.

Make sure that the voltage indicated on the identifi cation plate 
attached to the inside of the fi lter door corresponds to that of the 
mains supply (fi g. 13).

All cut-outs, electric wiring and mains sockets must have a rating such that 
enables them to support the maximum load indicated on the identifi cation plate.

Once the appliance has been installed, it must be connected to the mains supply 
through a single-pole switch.

The mains supply to which the appliance is connected must be fi tted with an 
earthing system. If this is not the case, the manufacturer will not be held liable 
for any incidents that may occur (fi g. 14).

If the mains socket to which the appliance is connected is faulty or unsuitable, 
it must be replaced by a qualifi ed electrician.

The washing machine must not be connected to the mains supply using indirect 
methods such as extension leads or multiple adapters.

During maintenance work, the washing machine must be disconnected from 
the mains electricity supply.

Do not insert or remove the plug from the mains socket with wet hands.

If the power supply cable is damaged in any way, contact the appropriate spe-
cialised service centre.

The plug used to connect the machine to the power supply must never be fi xed 
behind the machine, but must be in a position easily accessible in an emergency.

GB

CONNECTING TO THE MAINS ELECTRICITY SUPPLY

13

14

15

16

Open

Closed

Summary of Contents for WM747W















Reviews: