background image

1 - COMPONENT INSTALLATION

A - INSTALLATION OF REAR ANCHOR BRACKETS

 

* Refer to INSTALLATION GUIDELINES section entitled "Rear track systems"

B - INSTALLATION OF FRONT ANCHOR BRACKETS

* Refer to INSTALLATION GUIDELINES section entitled "Front track systems"

C - INSTALLATION OF STEERING LIMITERS 

(if applicable)

2 - COMPONENT ADJUSTMENT

 

A - ANGLE OF ATTACK

* Refer to ADJUSTMENTS section entitled "Angle of attack"

B - TRACK ALIGNMENT

* Refer to ADJUSTMENTS section entitled "Track alignment"

C - TRACK TENSION

* Refer to ADJUSTMENTS section entitled "Track tension"

D - STEERING LIMITER ADJUSTMENT 

(if applicable)

* Refer to INSTALLATION GUIDELINES section entitled "Front track systems"

3 - INTERFERENCE CHECK

4 - TEST RUN

5 - POST TEST RUN FINAL CHECKS 

A - ANGLE OF ATTACK

 

* Refer to ADJUSTMENTS section entitled "Angle of attack"

B - TRACK ALIGNMENT

* Refer to ADJUSTMENTS section entitled "Track alignment"

C - TRACK TENSION

* Refer to ADJUSTMENTS section entitled "Track tension"

        1.5 km (1 mile) TEST RUN

* Refer to INSTALLATION GUIDELINES section entitled "Front track systems" . ** Do not 
adjust the Steering Limiter sets before having adjusted the angle of attack.                    

IN THE EVENT OF INTERFERENCE BETWEEN THE VEHICLE AND TRACK SYSTEM, SOME PARTS ON 
THE VEHICLE MAY HAVE TO BE REMOVED OR MODIFIED, OR A LIFT KIT MAY HAVE TO BE 
INSTALLED. IF APPLICABLE, SEE INSTALLATION GUIDELINES SECTION ENTITLED "COMPLETION".

CAMSO ATV R4S TRACK SYSTEMS

INSTALLATION AND ADJUSTMENT CHECKLIST

** Steps in this checklist are laid out in logical order. They should be performed in 

succession to optimize the track system installation on the vehicle. **

-------------------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------------------

-------------------------------------------------------------------------------------------------------------------------------------------

------------------------------------------------------------------------------------------------------------------------------------------

-----------------------------------------------------------------------------------------------------------------------------------------

Summary of Contents for ATV R4S












Reviews: