Camtec 3041101002CA Manual Download

Page: 4 / 19

CPS-EP2000(R2) MANUAL

Camtec Power Supplies GmbH - Gewerbestrasse 30 - DE-76327 Pfinztal / Germany

P.4/19 (01/2018.01.1)

Tel. +49 (721) 46596 - 0 Fax +49 (721) 46596 - 77

www.camtec-gmbh.com

info@camtec-gmbh.com

(Subject to alterations. This product is not designed to be used in applications such as life support systems wherein a failure or malfunction could result in injury or death)

Technical Data Table

AC Input Range

184 – 264Vac

AC Input Frequency

47 – 63Hz

DC Input Range

250 – 375Vdc

AC Input Rated

230Vac <10,0A

DC Input Rated

250Vdc <9,3A 375Vdc <6,2A

DC Voltage Rated

24Vdc

36Vdc

48Vdc

72Vdc

110Vdc

DC Voltage Setting Range

24 - 30Vdc

30 - 45Vdc

45 - 58Vdc

58 - 90Vdc

90 - 150Vdc

DC Current Rated

84A

56A

42A

28A

18,2A

Over Voltage Protection

35Vdc

52,5Vdc

68Vdc

105Vdc

175Vdc

Over Current Protection

85,7A

57,1A

42,8A

28,6A

18,6A

Ripple Noise 230Vac 20MHz 35mVpp

35mVpp

75mVpp

100mVpp

200mVpp

Power Rated

2000W, 184-264Vac

Cooling

Continuously controlled and monitored fans from EBM Papst (Germany)

Efficiency

typ. 92-94% 230Vac at full load

Power Factor Control (PFC) 0,99 / 230Vac full load
Short Circuit Resistance

yes

Open Circuit Protected

yes

Base Load (OCP)

Non required (open circuit protected)

Load Regulation

< ± 0,05% 0-100%

Load Regulation Time

<1ms on load switch 10-100%

Accuracy Imon

≤

± 1%

Temperature Control

yes, thermal shutdown & autorecovery (+70°C, outside measuring point distance 10mm)

Hold Up Time

>30ms 230Vac

mains buffering at full load

Inrush Current

<14,6Aeff <20,7Apeak 230Vac active electronic inrush protection (no simple NTC)

Startup Delay

typ. 1s

Softstart

typ. 100ms

Ambient Temperature

- 20°C…+60°C operating, derating 2,5%/°C >50°C

Storage Temperature

- 40°C…+85°C

Ambient Conditions

Humidity 95% non-condensing @ 25°C, climate class 3K3, pollution degree 2

ROHS

2011/65/EU, (EU) 2015/863 conform

REACH

EG No. 1907/2006 conform

EMI

EN55032, conducted .024/.036/.048 class B / .072/.110 class A, all models radiated class A

EMS/EMI

EN61000-6-2,3,4

Safety

EN61010-1, EN61010-2-201, EN62368-1, EN60950-1, EN60204-1

Protection Class I

PE connection required

Leakage Current

Typical 1.9mA, <2.8mA, 230Vac 50Hz

Isolation Input to Output

3000Vac

Isolation Input to Case

2500Vac

Isolation Output to Case

500Vdc ,

≥

48Vdc= 2800Vdc

MTBF (IEC61709)

419000h (Meantime Between Failures: statistic time between failures after repairs)

MTTF (IEC61709)

146105h (Meantime To Failure: statistic time to ever fails)

Dimensions (HxWxD)

84x126,4x444mm | 3,3x5x17,5 Inch (without frontplate, note cable outlet in planning)

Weight

4,4kg / 9,7lbs

Input Power Connections

Neutrik NAC3FCA (locked by bajonett) included

Output Power Connections

Brass-Powerbars with metric M8 thread, a touch protection is included

Output Ratings

Model

24Vdc

36Vdc

48Vdc

72Vdc

110Vdc

Slew Rate 90-10%, 10/100% Load, [ms] typ.

70/7,0

30/3.0

46/4,6

35/3,5

47/4,7

Output Capacity, [mF] typ.

19,4

3,74

3,4

1,07

0,52

Summary of Contents for 3041101002CA




















Search results

Summary of Contents for 3041101002CA

Reviews:

Related manuals for 3041101002CA

Brands by name

Popular brands

Camtec 3041101002CA, Manual

Search results

Summary of Contents for 3041101002CA

Reviews:

Related manuals for 3041101002CA

Brands by name

Popular brands