background image

 

23 

 

DynaFLO LIMITED WARRANTY 

 
GENERAL 

CAMUS Hydronics 

Limited (“CAMUS”) extends the following LIMITED WARRANTY to the owner of this appliance, provided 

that the product has been installed and operated in accordance with the Installation Manual provided with the equipment. 
CAMUS will furnish a replacement for, or at CAMUS option repair, any part that within the period specified below, shall fail in 
normal use and service at its original installation location due to any defect in workmanship, material or design. The repaired 
or replacement part will be warranted for only the unexpired portion of the original warranty. This limited warranty does not 
cover failures or malfunctions resulting from: (1) Failure to properly install, operate or maintain the equipment in accordance 
with CAMUS’ manual; (2) Abuse, alteration, accident, fire, flood, foundation problems and the like; (3) Sediment or lime build-
up, freezing, or other conditions causing inadequate water circulation; (4) Pitting and erosion caused by high water velocity; (5) 
Failure of connected systems devices, such as pump or controller; (6) Use of non-factory authorized accessories or other 
components in conjunction with the system; (7) failing to eliminate air from, or replenish water in, the connected water system; 
(8) Chemical contamination of combustion air or use of chemical additives to water; (9) Production of noise, odours, 
discolouration or rusty water; (10) Damage to surrounds or property caused by leakage or malfunction; (11) All labour costs 
associated with the replacement and/or repair of the unit; (12) Any failed component of the hydronic system not manufactured 
as part of the product. 
 

HEAT EXCHANGER 

Within 18 months of the appliance having declared FOB from CAMUS, a heat exchanger shall prove upon examination by 
CAMUS to be defective in material or workmanship, CAMUS, at its option, will exchange or repair such part or portion if 
deemed warranty. Camus shall accept no responsibility if the heat exchanger has been improperly installed, operated, or 
maintained, or if any unauthorized modification, adjustment, and/or repairs have been made to the item. 
 
The exchanged or repaired heat exchanger will carry the balance of the remaining original warranty provided with the 
appliance based on the FOB date. In the event a replacement heat exchanger is delivered and if the defective heat exchanger 
is deemed to be repairable by CAMUS the repaired heat exchanger will be returned to the customer and a credit will not be 
issued.  
 

ANY OTHER PART 

If any other part fails within one (1) year after installation, or eighteen (18) months of the appliance having declared FOB from 
CAMUS whichever comes first CAMUS will furnish a replacement or repair that part. Replacement parts will be shipped FOB 
our factory. 
 

DURATION OF LIMITED WARRANTY 

Any limited warranty, including the warranty of merchantability imposed on the sale of the product under the laws of the state 
or province of sale are limited in duration to one year from date of original installation. 
 

STATE LAW & LIMITED WARRANTY 

Some states or provinces do not allow: 

a)  Limitations on how long an implied warranty lasts 
b)  Limitations on incidental or consequential damages. 

The listed limitations may or may not apply to you. This warranty gives you specific legal rights, and you may also have other 
rights which may vary from state to state and province to province. 
 

CONDITIONS 

We will not: 

a) 

Repair or replace any product, or part, subject to conditions outlined in ‘This Limited Warranty Does Not Cover’ 

b)  Reimburse any costs associated with repair and/or replacement 
c)  Replace and/or repair any product without complete model number/serial number 
d)  Replace any product without prior receipt of actual rating plate from the appliance. 

 

HOW TO MAKE A CLAIM 

Any claim under this warranty shall be made directly to CAMUS Hydronics Limited Representative in your area. Please visit 
our website at www.camus-

hydronics.com and use our “Rep Finder” tool to locate your local CAMUS representative. 

 

SERVICE LABOR RESPONSIBILITY 

CAMUS shall not be responsible for any labour expenses to service, repair or replace the components supplied. Such costs 
are the responsibility of the owner. 
 

DISCLAIMERS 

CAMUS shall not be responsible for any water damage. Provisions should be made that in the event of a water/appliance or 
fitting leak, the resulting flow of water will not cause damage to its surroundings. 
 

 

Summary of Contents for DynaFLO DOWB-S1 Series





























Reviews: