background image

Controllers Area Networks Inc. 

 

Smart Tweezers User Manual Version 1.0 

Page 16 of 16 

 

LABELLING & VERIFICATION REQUIREMENTS 

 

This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference and (2) 
this device must accept any interference received, including interference that may 
cause undesired operation. 
 
 

WARRANTY 

Dear Madam/Sir,                                                   
You are now the owner of 

Smart Tweezers

 

Meter, a product that ranks the first of its kind 
in the world.                                                           
 
CAN Inc. provides 

12 months

 warranty from 

the original date of purchase against defective 
material and workmanship. 
In the unlikely event of failure of this meter 
within the warranty period, CAN Inc. 
undertakes to get the meter repaired free of 
charge. Please hand over the meter to the 
dealer from whom you have purchased along 
with this WARRANTY CARD and relevant 
Cash memo/ Invoice. This warranty entitles you 
to bring the meter at your cost to the nearest 
dealer and collect it after repair.  
                                                                              

NO TRANSPORTATION CHARGES WILL BE 

REIMBURSED.     

 

 

The warranty is not valid in the following cases:  

1.  Warranty card duly signed and stamped and original cash memo/invoice is not sent along 

with meter. 

2.  Defect caused by misuse, neglect, accidents, or tampering. 
3.  Improper repairing by any person not authorized by the company. 
4.  Modification, alteration of any sort made to electrical circuitry. 
5.  Seal provided inside is broken. 
6.  Complete warranty card is not presented to an authorized person at the time of repair. 

 

                                                          

                                             

Summary of Contents for Smart Tweezers

















Reviews: