T H U N D E R B A Y S E
Spa Functions
Pumps
Press the “Jets 1” button once to turn pump 1 on or off, and to
shift between low- and high-speeds if equipped. If left running,
the pump will turn off after a time-out period. The pump 1
low-speed will time out after 30 minutes. The high-speed will
time out after 15 minutes.
The low-speed of pump 1 runs when the other pump is on. If
the spa is in Ready Mode, Pump 1 low may also activate for at
least 1 minute every 30 minutes to detect the spa temperature
(polling) and then to heat to the set temperature if needed.
When the low-speed turns on automatically, it cannot be deac-
tivated from the panel, however the high speed may be started.
Filtration and Ozone
Pump 1 low and the ozone generator will run during filtration.
The system is factory-programmed with two filter cycles that
will run 10 minutes after power-up. The filter duration is
programmable. At the start of each filter cycle, Pump 2 will run
briefly to purge its plumbing to maintain good water quality.
Freeze Protection
If the temperature sensors within the heater detect a low
enough temperature, then the pump(s) automatically activate
to provide freeze protection. The pump(s) will run either
continuously or periodically depending on conditions.
In colder climates, an optional additional freeze sensor may
be added to protect against freeze conditions that may not be
sensed by the standard sensors. Auxiliary freeze sensor
protection acts similarly except with the temperature
thresholds determined by the switch. See your dealer for details.
Clean-up Cycle
When a pump is turned on by a button press, a clean-up cycle
begins 30 minutes after the pump is turned off or times out.
The pump and the ozone generator will run for 30 minutes or
more, depending on the system.
Temperature and Temp Range
Adjusting the Set Temperature
When using a panel with Up and Down buttons (Temperature
buttons), pressing Up or Down will cause the temperature to
flash. Pressing a temperature button again will adjust the set
temperature in the direction indicated on the button. When the
LCD stops flashing, the spa will heat to the new set
temperature when required.
If the panel has a single temperature button, pressing the
button will cause the temperature to flash. Pressing the button
again will cause the temperature to change in one direction
(e.g. UP). After allowing the display to stop fl ashing, pressing
the Temperature Button will cause the temperature to flash
and the next press will change the temperature in the opposite
direction (e.g. DOWN). The temperature can be set between
16°C and 40°C (60°F and 104°F).
Press-and-Hold
If a Temperature button is pressed and held when the
temperature is flashing, the temperature will continue to
change until the button is released. If only one temperature
button is available and the limit of the Temperature Range is
reached when the button is being held, the progression will
reverse direction.
PUMPS
5 HP Big Red 2 Speed pumps
Our 5 HP pump is the most powerful spa
pump in the market with our oversize
intakes.
2” Twin Roto jet
Adjustable and interchangeable jet spins
and pulsates. The jet can be removed by
turning it counter-clockwise. To replace the
jet push inward and clockwise until it clicks
into place.
3” Directional jet
Adjustable and interchangeable jet features
a directional nozzle. The jet can be removed
by turning it counter-clockwise. To replace
the jet push inward and clockwise until it
clicks into place.
3” Massage jet
Adjustable and interchangeable jet which
spins to deliver a soothing massage. The jet
can be removed by turning it counter-
clockwise. To replace the jet push inward
and clockwise until it clicks into place.
2” Directional jet
Adjustable and interchangeable jet features a
directional nozzle. The jet can be removed by
turning it counter-clockwise. To replace the jet
push inward and clockwise until it clicks into
place.
5” (Jumbo) Directional jet
Adjustable and interchangeable jet features a
directional nozzle. The jet can be removed by
turning it counter-clockwise. To replace the jet
push inward and clockwise until it clicks into
place.
5” Massage jet
Adjustable and interchangeable jet features an
internal spinner to deliver a low pressure sooth-
ing massage. The jet can be removed by turning
it counter-clockwise. To replace the jet push
inward and clockwise until it clicks into place.
2” Point jet
Standard jet is permanently on and supplies
heated water continually. The jet can be
removed by turning it counter-clockwise. To
replace the jet push inward and clockwise
until it clicks into place.
Air Controller
These are located around the top of your spa.
Increase or decrease the force of your jets by
opening or closing the air control valves.
Aroma basket cap
Open cap to place aromatherapy beads. Close
after use.
Waterfall control
Located on the topside of the spa, this valve
adjusts water flow to the waterfall.
HOW JETS WORK
Air is mixed with the water by using the air controls to create massage(s) of varying degrees. Water flow is adjusted by simply
turning the outer face of the full sized jets. Our hot tubs have a combination of pulsating, rotating, and directional adjustable jets.
(15)
