background image

 Canarm Tri-Lite 3LEC Series

Contents

Tri-Lite 3LEC Airfoils (

patent pending

)

Tri-Lite 3LEC Control and Power Assembly (

patent pending

)

Model 

Description 

Length

Width

Height

Shipping Weight

Tri-Lite 3LEC

Control & Power Assembly

30.5”

33.0”

30.5”

215 lbs.

Model 

Description 

Width (X) 

Length (Y) 

Height (Z)

Shipping Weight

3L06EC-[V][P]

6’

32.0”

94.0”

19.0”

50 lbs.

3L08EC-[V][P]

8’ 

32.0”

94.0”

19.0”

55 lbs.

3L10EC-[V][P]

10’

32.0”

94.0”

19.0”

60 lbs.

3L12EC-[V][P]

12’

32.0”

94.0”

19.0”

65 lbs.

3L14EC-[V][P] 

14’

32.0”

94.0”

19.0”

70 lbs.

3L16EC-[V][P] 

16’

32.0”

94.0”

19.0”

80 lbs.

3L18EC-[V][P]

18’

32.0”

142.0”

19.0”

100 lbs.

3L20EC-[V][P]

20’

32.0”

142.0”

19.0”

110 lbs.

3L24EC-[V][P]

24’

32.0”

142.0”

19.0”

120 lbs.

 1

 

Fan Diagram ....................................................................................................................................6

 2

 

Important Information  ..................................................................................................................7

 3

   Mounting Considerations  .............................................................................................................8

 4

   Preparing the Work Site .................................................................................................................9

 5

   Mounting Method 1: I-Beam  ......................................................................................................10

 6

   Mounting Method 2: Angle Iron  ..........................................................................................11-15 

 

Mounting Method 3: Purlins  ................................................................................................16-17 

 

Mounting Method 4: Upper Truss  .......................................................................................18-19

 7

   Hanging the Fan  .....................................................................................................................20-21

 8

   Installing Guy Wires/Gripple ................................................................................................22-23

 9

   Installing Airfoils and Motor Hub  .......................................................................................24-27

10

 Electrical 

 ..................................................................................................................................28-32

11

   Troubleshooting  ............................................................................................................................33

12

   User Servicing Instructions  ...................................................................................................34-35

*

[V]

 = 230 or 460 Volts, 

[P]

 = 1 or 3 Phase. 

Sample Model Number:

 3L08EC-4603

Summary of Contents for 3LEC Series





































Reviews: