background image

 

Using the Raven II CDPD Modem – Canary Systems Application Note #12 – March 2002 – Page 2 of 8 

Raven II Configuration 

 
The Raven II Modem is usually configured using the 

Wireless Ace

 software from Airlink. This software is 

available without charge from Airlink at the following link: 

www.airlink.com/ace

 

 
Configuration consists of setting the values of a series of registers in the modem, the list of registers may 
be displayed and modified by selecting the option 

Tools | Configuration

 
The complete list of registers and the recommended settings is shown below. 
 

Note: Register 53 shown below must use the IP, in the format shown, that has been obtained from 
the service provider! 

 

[\N]   Side Preference=3 
[S110] Device Port=3001 
[S116] Service ID Preference=3 
[S111] Service ID=0/0/0 
[S112] Channel List Mode=2 
[S113] Channel List=715,706,708,790,793,792,796,794,791,798,795,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 
[3W] 3 Watt Booster Support=0 
[*DSIDE] Disable Side Switch=0 
[#X] Debug Output=0 
[S0]   TCP Auto Answer Mode=1 
[S7]   TCP Establishment Timeout=20 
[S50]  Data Forwarding Timeout=1 
[S51]  Data Forwarding Character=0 
[S53]  Destination IP Address=000.000.000.000 
[S53]  Destination TCP/UDP Port=23 
[S53]  Destination Connect Mode=T 
[S210] AT Command Compatibility=1 
[S211] Ignore DTR=1 
[MD] Startup Mode Default=0 
[MD] UDP Mode Default=0 
[S60] Telnet Echo Mode=0 
[S82] UDP Half Open Mode=0 
[S83] UDP Half Open Timeout=0 
[AIP] Allow Any UDP IP=0 
[HOR] UDP Half Open Response=0 
[S220] Break On TCP Connect=0 
[S221] Delay Connect Response=0 
[E] Command Echo=1 
[V] Command Response Mode=1 
[Q] Quiet Mode=0 
[X] Call Progress Result Mode=0 
[TCPT] TCP Inactive Timeout=5 
[TCPS] Specify TCPT in Seconds=0 
[TCPX] Allow TCP Suspension=0 
[*DATZ] Disable Reset on ATZ=1 
[DAE] Disable AT Esc Sequence=1 
[RKEY] Radio Transceiver Keying=0 
[\Q] Flow Control=0 
[S23] Baud Rate=9600 
[S23] Data Bits=8 
[S23] Parity=N 
[MVOFF] Modbus-Variant Offset=1 
[MVLEN] Modbus-Variant Length=0 
[MVTYP] Modbus-Variant Type=0 
[MVOPT] Modbus-Variant Options=0 
[MVMSK] Modbus-Variant ID Mask=0 
[FM] Friends Mode=0 

Summary of Contents for Raven II CDPD









Reviews: